Grizzly G0677 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 96

background image

-44-

G0677 24" Planer/Sander

Belt Tracking

Adjustments

The belt tracking adjustments have been per-
formed at the factory and should require no fur-
ther attention. However, we recommend that you
verify the settings.

When correctly adjusted, the belt should take
about the same amount of time to travel from one
side of the upper roller to the other .

If  you  notice  that  the  belt  is  tearing,  is  tracking
toward one side more than the other, or contacting
a  limit  switch  and  causing  the  emergency  brake
to  stop  the  machine,  belt  tracking  needs  to  be
adjusted.

Tools Needed:

Qty

Wrench 9mm ..................................................... 1
Pencil or Pen ..................................................... 1

To check and adjust belt tracking:

1. Be sure the sanding belt is properly installed

and the belt is tensioned, then DISCONNECT
THE PLANER/SANDER FROM THE POWER
SOURCE AND REMOVE AIR PRESSURE!

2. Open the upper left access door.

3. Visually check that the belt tracking adjust-

ment knob (

Figure 50) is centered, as shown

in

Figure 51.

—If the knob is not centered, turn the knob

counterclockwise to loosen it, move it to
the center position—between 11 and 1
o'clock—as viewed straight on, then tight-
en the knob.

4. Open the upper right access door, loosen the

lock nuts on the airflow adjustment knob and
the oscillation speed control knob.

Centered

Left

Right

Figure 51. Belt tracking knob positions.

Figure 50. Oscillation adjustment knob.

Oscillation

Adjustment

Knob

5.

Turn both knobs counterclockwise all the
way.

6. Make a reference mark using a pencil or pen

at the 12:00 position, turn each knob clock-
wise 3

1

⁄

2

turns, then tighten the lock nuts.

This will reset the knobs to the factory setting
and ensure there is an adequate amount of
airflow through the air fork air jet so the upper
roller pivots and the belt oscillates.

7. Connect the machine to power and air, and

while pressing the upper left access door
safety switch in, turn the sanding belt

ON.

8. Observe the oscillation of the sanding belt. It

should take the belt approximately the same
amount of time to oscillate from one side to
the other.

—If the belt oscillates to the left and right the

same amount of time, no further adjust-
ments are needed.

Figure 52. Airflow and oscillation speed control

knob.

Airflow

Adjustment

Speed

Control

«
...
44
45
46
47
48
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Nakamichi Страницы: 62

Бренд: Jensen Страницы: 7

SLMP50 - PORT. CD PLAYER

Бренд: Panasonic Страницы: 8

AZ7000 - Cd Personal

Бренд: Magnavox Страницы: 22

Бренд: Denon Страницы: 58

Бренд: Kenwood Страницы: 24

CD Walkman D-EJ001

Бренд: Sony Страницы: 2

CD Walkman D-EJ011

Бренд: Sony Страницы: 2

CD Walkman D-EG7

Бренд: Sony Страницы: 2

CD Walkman D-EG3

Бренд: Sony Страницы: 2

CD Walkman D-EG3

Бренд: Sony Страницы: 2

CD Walkman D-E551

Бренд: Sony Страницы: 2

CD Walkman D-193

Бренд: Sony Страницы: 2

Car Discman D-M805

Бренд: Sony Страницы: 16

CD Walkman D-E770

Бренд: Sony Страницы: 18

CD Walkman D-EG7

Бренд: Sony Страницы: 25

CD Walkman D-E880

Бренд: Sony Страницы: 23

CD Walkman D-EG3

Бренд: Sony Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды