Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 4 / 96

background image

-2-

G0677 24" Planer/Sander

INTRODUCTION

We stand behind our machines. If you have any
service questions, parts requests or general ques-
tions about the machine, please call or write us at
the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: [email protected]

If you have any comments regarding this manual,
please write to us at the address below:

Grizzly Industrial, Inc.

C

/

O

Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Contact Info

This machine is designed to remove the top sur-
face of a workpiece then sand it smooth so it is
ready for finish spraying or other uses.

In a typical operation, the operator sets the depth
of cut, turns the sanding drum and feed motors

ON, sets the speed of the feed belt, then feeds
the workpiece into the machine.

The feed belt moves the workpiece under the
cutterhead and sanding drum, then out the other
side. The workpiece can be fed through additional
times until the desired thickness and finish are
achieved.

The  oscillation  system  shifts  the  sanding  belt
from side-to-side on the sanding drum to produce
an  even  sanding  finish  across  the  width  of  the
workpiece.  The  sanding  motor  brake  unit  brings
the  cutterhead  and  sanding  belt  to  a  quick  stop
when the power is turned

OFF.

Functional Overview

Manual Accuracy

We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings, and
photographs of the machine we used when writ-
ing this manual. However, sometimes errors do
happen and we apologize for them.

Also, owing to our policy of continuous improve-
ment,

your machine may not exactly match

the manual. If you find this to be the case, and
the difference between the manual and machine
leaves you in doubt, immediately call our techni-
cal support for updates or clarification.

For your convenience, we always keep current
Grizzly manuals and most updates available on
our website at

www.grizzly.com. Any updates to

your machine will be reflected in these documents
as soon as they are complete. Visit our site often
to check for the latest updates!

«
...
2
3
4
5
6
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Parkside Страницы: 28

Бренд: Roadstar Страницы: 76

Бренд: Rotel Страницы: 10

CHX1500 - CD Changer

Бренд: JVC Страницы: 65

ZS-XN30 - Cd Boombox

Бренд: Sony Страницы: 2

CDX-525RF - Compact Disc Changer System

Бренд: Sony Страницы: 20

Бренд: Sony Страницы: 26

Бренд: Sony Страницы: 28

ZS-XN30 - Cd Boombox

Бренд: Sony Страницы: 32

Бренд: Sony Страницы: 34

Бренд: Sony Страницы: 32

ZS-XN30 - Cd Boombox

Бренд: Sony Страницы: 56

Бренд: Sony Страницы: 54

Бренд: Sony Страницы: 50

Бренд: Audionet Страницы: 58

Бренд: Audionet Страницы: 60

WOODWORKER CON1020

Бренд: Clarke Страницы: 16

Бренд: Durabrand Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды