Grizzly G0677 Скачать руководство пользователя

Страница: 55 / 96

G0677 24" Planer/Sander

-53-

4. Place a new matching pair of sanding drum

V-belts onto the idler roller and also roll on
the idler V-belts.

5. While holding the idler roller bracket up, have

an assistant install the sanding drum V-belts
onto the sanding drum pulley, then push the
idler pulley bracket back onto the rear stud.

6. Fasten the idler pulley bracket with the hex

bolt removed earlier, making sure the bracket
is flush with the plate shown in

Figure 73.

10. Move the idler pulley adjustment bracket off

of the rear stud, then roll the idler V-belts off
of the back of the pulley. Jostle the bracket a
little if it is difficult to remove.

11. Roll a new set of V-belts onto the idler pulley

and the motor pulley.

12. Reverse Steps 2-10 to re-install the idler

wheel adjustment bracket, caliper assembly,
and the cutterhead V-belts.

13. Tension all the V-belts: The belts are properly

tensioned when they will not move more than

⁄

" in the center when pushed with your finger

with moderate pressure, as shown in

Figure

67 on Page 51.

Sanding Drum V-Belts

1. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

2. Follow the instructions for removing the

cutterhead and idler V-belts (

Steps 1–10,

Idler V-belts on Page 52).

3. Lift the idler pulley adjustment bracket off of

the sanding drum V-belts, set it aside, then
remove the sanding drum V-belts.

Have an assistant help you during the fol-

lowing step. The idler pulley adjustment

bracket is heavy. Serious personal injury

could occur if you drop it on your body!

Figure 73. Location of hex nut securing idler

adjustment bracket to frame.

Idler Pulley
Adjustment

Bracket

Hex

Nut

Plate

9. Remove the hex nut that secures the idler

wheel adjustment bracket to the frame (

Figure

73).

7. Roll the idler V-belts off of the motor pulley.

8. Loosen the lock nuts on the idler pulley

adjustment bracket (see

Figure 69 on Page

51).

Figure 72. Nuts securing caliper.

6. Loosen and remove the two hex bolts and

washers that secure the caliper assembly
(

Figure 72), then move it out of the way.

Hex Bolts

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды