GRAPHTEC CE200-120 страница 88 Скачать руководство пользователя

Страница: 88 / 94

A – 2

Item

Specifications

Model number

CE2000-60

CE2000-120

Configuration

Grit-rolling cutting plotter

Drive system

Digital servo drive system

Maximum cutting area

584 mm

50 m

1220 mm

50 m

Range of guaranteed precision

584 mm

5 m*

1220 mm

5 m*

Compatible media widths

Minimum: 50 mm,

Minimum: 85 mm,

maximum: 712 mm

maximum: 1346 mm

(28 inches)

(53 inches)

Maximum media thickness

10 mil (0.25 mm)

Maximum cutting speed

60 cm/s

100 cm/s*

Specifiable cutting speeds

1 to 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 (cm/s)
The CE2000-120 has an additional setting of

∗∗

(100

cm/s).

Cutting force

20 to 300 g/f (31 levels)

20 to 450 g/f (39 levels)

Minimum character matrix

About 5 mm for an alphanumeric character (varies
with the medium, font, etc.)

Mechanical step size

0.005 mm

Programmable step size

GP-GL: 0.1, 0.05, 0.025, 0.01 mm; HP-GL*

: 0.025 mm

Repeatability precision

0.1 mm or less/2 m*

No. of mountable pens

1 pen

Compatible cutter type

Supersteel blades

Compatible pen type

Water-based fiber-tip pens

Compatible cutting media

Marking film (polyvinyl, fluorescent, or reflective film)
with a maximum thickness of 0.25 mm (excluding
high-luminosity reflective film)

Standard interfaces

RS-232C serial or Centronics-compatible parallel
(automatically selected)

Internal memory capacity

2 Mbytes

Command modes

GP-GL and HP-GL (selected at the control panel)

Display panel

Liquid crystal display, 16 characters

2 rows

Power supply

Supply voltage

115 to 230 VAC 50/60 Hz (UL, CSA)
100 to 240 VAC 50/60 Hz (CE)

Power consumption

80 VA

120 VA

Environmental

Operating environment

to 35

C, 35% to 75% R.H.

conditions

(non-condensing)

Guaranteed precision

to 32

C, 35% to 70% R.H.

(non-condensing)

External dimensions

840 (W)

278 (D)

250 (H) mm 1489(W)

656(D)

1189(H) mm

(including stand)

Weight

13 kg

46 kg (including stand)

Varies with the type of Graphtec-authorized film and the cutting conditions.

HP-GL is a registered trademark of Hewlett-Packard Company.

Only in the diagonal (45

angle) direction.

A.1 Main Specifications

Содержание CE200-120































































































Результаты поиска

Содержание CE200-120

Отзывы:

Похожие инструкции для CE200-120

Бренды по названию

Популярные бренды

GRAPHTEC CE200-120, Руководство пользователя

Результаты поиска

Содержание CE200-120

Отзывы:

Похожие инструкции для CE200-120

Бренды по названию

Популярные бренды