GRAPHTEC CE200-120 страница 83 Скачать руководство пользователя

Страница: 83 / 94

9 – 11

Error message

Cause

Solution

Execute a recognizable com-
mand.

Execute the command with the
correct number of parameters.

Execute the command with its
parameters specified within
their permissible ranges.

Specify a recognizable char-
acter set.

Execute the command with its
coordinate data specified within
the effective cutting/plotting
area.

Increase the buffer size.

Check the flow of your
programmed data.

Check the ESC commands in
your program.

Check the device control com-
mands in your program.

Check the program.

Check the number of command
parameters.

Check the settings of the inter-
face conditions.

Check the settings of the hand-
shaking mode and other inter-
face conditions.

An unrecognizable instruction was
executed.

A command was executed with the
wrong number of parameters.

A command containing an unusable
parameter was specified.

An unrecognizable character set was
specified.

A command was executed with co-
ordinate data that exceeds the effec-
tive cutting/plotting area.

The data being input exceeded the
capacity of the plotter’s download-
able character buffer, polygon buffer,
etc.

During execution of an output com-
mand, another output command was
executed.

The ESC character was followed by
an invalid byte.

A device control command contain-
ing an invalid byte was received.

A parameter outside of the permis-
sible numeric range was specified.

Too many parameters were received.

During data transfer, a framing error,
parity error, or overrun error occurred.

The I/O buffer received data at a
faster pace than it could process,
indicating that handshaking is not
successful.

ERROR 1
INSTRUCTION ERR

ERROR 2
PARAM NO. ERROR

ERROR 3
PARAMETER ERROR

ERROR 5
CHAR SET ERROR

ERROR 6
POSITION O/FLOW

ERROR 7
BUFFER OVERFLOW

ERROR 10 I/O
OUTPUT COMD ERR

ERROR 11 ESC
INVLD BYTE ERR

ERROR 12 I/O
CONTROL BYTE ERR

ERROR 13 I/O
PARAM RANGE ERR

ERROR 14 I/O
PARAM NO. ERROR

ERROR 15
I/O TRANSM ERR

ERROR 16 I/O
BUFFER OVERFLOW

Error messages in HP-GL emulation mode

Содержание CE200-120































































































Результаты поиска

Содержание CE200-120

Отзывы:

Похожие инструкции для CE200-120

Бренды по названию

Популярные бренды

GRAPHTEC CE200-120, Руководство пользователя

Результаты поиска

Содержание CE200-120

Отзывы:

Похожие инструкции для CE200-120

Бренды по названию

Популярные бренды