Grammer MSG 90.6PG Скачать руководство пользователя страница 60

Страница: 60 / 437

Repair Manual MSG 90.6PG Commercial Vehicles, Omnibuses – November 2017

Material no. 1153450_c

2.3

Overview of faults

Page 10 of 11

TABLE OF CONTENTS

Fault description

Possible cause

Troubleshooting

Backrest does not fold forwards by itself after
being unlocked.

• Torsion spring is detached.

• Tension spring is broken.

Hang in the torsion spring
(see Chapter 3.30

)

Replace the torsion spring
(see Chapter 3.30).

Backrest cannot be unlocked.

• Lever for backrest adjustment is

defective.

• Bowden pull wire for backrest

adjustment is not correctly adjusted.

• Bowden pull wire for backrest

adjustment is torn.

• Backrest locking mechanism is

defective.

Replace the lever for backrest
adjustment (see Chapter 3.13

)

Check the Bowden pull wire for
backrest adjustment and adjust it, if
necessary (see Chapter 3.12).

Replace the Bowden pull wire for
backrest adjustment
(see Chapter 3.13).

Replace the bearing support with
backrest locking mechanism
(Chapter 3.32).

Seat fore/aft adjustment does not operate
after pulling or pushing the lever for seat
fore/aft adjustment.

• Particles are between the adjusting

and locking rails.

Clean the seat fore/aft adjustment.

Содержание MSG 90.6PG






















































































































































































































































































































































































































































Результаты поиска

Содержание MSG 90.6PG

Отзывы:

Бренды по названию

Популярные бренды

Grammer MSG 90.6PG, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание MSG 90.6PG

Отзывы:

Бренды по названию

Популярные бренды