Grammer MSG 90.6PG Скачать руководство пользователя | Manualshive

Страница: 198 / 437

background image

Repair Manual MSG 90.6PG Commercial Vehicles, Omnibuses – November 2017

Material no. 1153450_c

3.20 Heater cable and belt tensioner cable (delivery option) –

removal and installation

Page 7 of 8

REMOVAL / INSTALLATION

TABLE OF CONTENTS

13 Pull out the clip (14) at the Z-section

(15) and detach the cable of the
heater switch (3) at the clip (14).

14 Mark the point where the cable for

vehicle connection (4) is attached to
the level control (16) by means of
cable ties (17) and remove the cable
ties (17).

15 For seat models Atego, Axor:

Mark the point where the cable for
vehicle connection (4) at the air
intake hose (20) and at the air
exhaust hose (19) is bundled by
means of cable tie (18) and remove
the cable tie (18).

Note:

For seat models with EPS cable,
the EPS cable is fastened by
means of cable ties as well
(see Chapter 3.21).

14

4

18

19

20

2

5

4

3

1

C

D

A

E

16

17

4

4

3

3

15

2188

«
...
196
197
198
199
200
...
»

Содержание MSG 90.6PG






















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSG 90.6PG

Бренд: JANE Страницы: 68

Бренд: Nuna Страницы: 35

Бренд: Cosatto Страницы: 57

Бренд: Miamily Страницы: 12

Бренд: Bright Starts Страницы: 32

Бренд: CYBEX Страницы: 68

Бренд: Baby Trend Страницы: 18

Бренд: Babyauto Страницы: 52

Бренд: BabySafe Страницы: 43

Бренд: Safeline Страницы: 32

Бренд: H-Germany Страницы: 63

Бренд: tuc tuc Страницы: 33

Sport HERO Reha

Бренд: RECARO Страницы: 8

Бренд: RECARO Страницы: 60

Бренд: RECARO Страницы: 92

Бренд: RECARO Страницы: 150

Бренд: RECARO Страницы: 184

Young Sport Hero

Бренд: RECARO Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды