Graco XD40 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

Graco XD40 Скачать руководство пользователя страница 32

Additional Repair and Replacement Instructions

32

332203F

15. Install outlet (30) to spool. Replace and tighten all

bolts (37) securely. Torque bolts to 24 to 30 ft.
pounds (32.54 to 40.67 N.m) (F

IG

. 68).

NOTE:

• Low Pressure Models (shown in F

IG

. 68) use 4

bolts (37).

• Medium Pressure Models (not shown) use 6

bolts (37).

• Always use all bolts provided.

16. Remove c-clamp (A) (installed in Step 13, page 31).

17. Disengage latch by pulling on hose to release it.

18. Use your hand to guide the hose as it rewinds onto

the reel.

19. Adjust spring tension if needed. See Adjusting

Spring Tension, page 35.

20. Remove cap from end of hose and install dispense

valve to end of hose.

Roller Guide Replacement

Disassembly

1.

Relieve pressure, page 10.

2.

Pull the hose out far enough to engage the latch.
Listen for the loud click when the spool has latched.

3.

Securely attach a c-clamp (A) to the reel spool as
shown in F

IG

. 69 to help prevent the reel from unin-

tentionally becoming unlatched and spinning freely.

F

IG

. 68: Low Pressure Model Shown.

Always wear heavy, non-slippery gloves when adjust-
ing the spring tension to protect your hands from being
cut on the hose reel.

30

37

Never allow the reel to spin freely. Doing so causes

the hose to spin out of control, which could cause
serious injury if you are hit by the hose or dispense
valve.

F

IG

. 69

A

«
...
30
31
32
33
34
...
»

Содержание XD40

















































Отзывы:

Нет отзывов