Graco XD40 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

Graco XD40 Скачать руководство пользователя страница 18

Hose Reel Disassembly

18

332203F

NOTE

: Place a piece of tape as a marker at the

location of the non-threaded hole (a) that does not
have a screw, located on the inlet side of the spool,
to ensure the inlet is reinstalled on the correct side
and in the correct position during reassembly.

If you are only replacing the Ratchet, stop disas-
sembly instructions here.

Ratchet Kit 24R338 is available from Graco. If you
are only replacing the Ratchet, stop disassembly
instructions here. Reassembly instructions are pro-
vided in Step 2, page 20.

If you are not replacing the ratchet, set these parts aside
to use for reassembly.

22.Remove Swivel (3) from spool.

d.

Remove swivel (3) from inside of spool (2) (F

IG

.

25).

Low Pressure Spring Swivel Replacement Kit
24R336 and Medium Spring Swivel Replacement Kit
24R337 are available from Graco. See Parts page 40,
for additional information about ordering these kits.
Reassembly instructions are provided in Step 1,
page 19.

23.Remove Shaft (11) from spool.

e.

Remove bolts (9) holding shaft (11) (spring

side) to the spool and remove shaft from inside

of spool.

C and D Spring Shaft Replacement Kit 24R953 and A
and B Spring Shaft Replacement Kit 24R954 are
available from Graco. See Parts page 40, for addi-
tional information about ordering these kits. Reas-
sembly instructions are provided in Step 3, page 20.

F

IG

. 24

F

IG

. 25

a

4

3

2

F

IG

. 26

11

2

9

«
...
16
17
18
19
20
...
»

Содержание XD40

















































Отзывы:

Нет отзывов