Graco XD40 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

Graco XD40 Скачать руководство пользователя страница 22

Hose Reel Reassembly

22

332203F

7. Install spool (2) on reel frame (1).

8. Visually inspect inlet seal and o-ring.

Also, use your finger to feel surface of seal and
o-ring for nicks. Replace these parts if damaged.

To replace seals:

a.

Use a pick to remove the damaged white seal

(33a) and black o-ring (33b) from the inlet

assembly (6) (F

IG

. 36).

b.

Apply a thin layer of grease to the black o-ring

(33b) and white seal (33a).

c.

Install the new black o-ring (33b) first. Use your

fingers to press it into the groove located inside

the neck of the inlet assembly (6) (F

IG

. 37).

NOTE:

Folding the o-ring into a U-shape before

installation will help seat it correctly inside the

inlet assembly. Then use your fingers to press

the o-ring into the groove.

d.

Install the white seal (33a) over the o-ring (33b)

(F

IG

. 38).

NOTE:

Folding the seal into a U-shape before

installation will help seat it correctly inside the

inlet assembly. Then use your fingers to press

the seal into the groove.

NOTE:

Be careful when installing these parts that they

are lying flat inside the groove and do not have any
kinks or bends which could result in fluid leakage due to
a poorly seated seal.

F

IG

. 35

NOTICE

Be careful not to scratch or score the surface of the
inlet (6) when using the pick to remove the seal (33a)
and o-ring (33b) . Damage to this surface could result
in fluid leakage.

F

IG

. 36

2

1

6

33b

33a

F

IG

. 37

F

IG

. 38

33b

6

33a

6

«
...
20
21
22
23
24
...
»

Содержание XD40

















































Отзывы:

Нет отзывов