Graco XD40 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

Graco XD40 Скачать руководство пользователя страница 29

Additional Repair and Replacement Instructions

332203F

29

12. Verify outlet o-ring (34) is in place on outlet (30).

Apply a thin layer of grease (G) to o-ring as shown
in F

IG

. 60.

d.

Install outlet (30) to spool. Replace and tighten

all bolts (37) securely. Torque bolts to 24 to 30

ft. pounds (32.54 to 40.67 N.m) (F

IG

. 61).

NOTE:

• Low Pressure Models (shown in F

IG

. 51) use 4

bolts (37).

• Medium Pressure Models (not shown) use 6

bolts (37).

• Always use all bolts provided.

13. Uncoil and extend hose.

14. Remove c-clamp (A) (installed in Step 7, page 28).

15. Disengage latch by pulling on hose to release it.

16. Use your hand to guide the hose as it rewinds onto

the reel.

17. Adjust spring tension if needed. See Adjusting

Spring Tension, page 35.

18. Remove cap from end of hose and install dispense

valve to end of hose.

F

IG

. 60

F

IG

. 61: Low Pressure Model Shown

(G)

30

34

30

37

Always wear heavy, non-slippery gloves when adjust-
ing the spring tension to protect your hands from being
cut on the hose reel.

«
...
27
28
29
30
31
...
»

Содержание XD40

















































Отзывы:

Нет отзывов