Graco XD40 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

Graco XD40 Скачать руководство пользователя страница 31

Additional Repair and Replacement Instructions

332203F

31

8.

Apply pipe thread sealant or wrap hose threads with
PTFE tape.

9.

Attach end of the hose to the outlet (30) using two
wrenches on the flats, working in opposite direc-
tions, to securely tighten the hose to the outlet fitting
(F

IG

. 65).

10. Place a piece of tape on the side of the reel flange

as a visual reference point for counting reel rota-
tions.

11. Pre-wind hose reel as needed to accommodate the

length of hose you are installing. Refer to Table 1,
Spring Tension and Pre-Turns, page 47 to deter-
mine the number of turns needed for your hose and
reel model.

NOTE:

Wind direction is determined by the direction

the spool rotates when the hose is extended during
operation.

12. Engage the latch. Listen for the loud click when the

spool has latched.

13. Securely attach a c-clamp (A) to the reel spool as

shown in F

IG

. 66 to help prevent the reel from unin-

tentionally becoming unlatched and spinning freely.

14. Verify outlet o-ring (34) is in place on outlet (30).

Apply a thin layer of grease (G) to o-ring as shown
in F

IG

. 67.

F

IG

. 65

Never allow the reel to spin freely. Doing so causes

the spool to spin out of control, which could cause
serious injury if you are hit by the hose or dispense
valve.

30

F

IG

. 66

F

IG

. 67

A

(G)

30

34

«
...
29
30
31
32
33
...
»

Содержание XD40

















































Отзывы:

Нет отзывов