Graco 309028ZAT Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 98

background image

Component Identification

309028ZAT

19

Junction Box Panel (H)

. 6 on page 16.

The Junction Box Panel (H) includes the following
system components. For additional information, refer to
the

Electrical Diagram

on page 91.

•

SYSTEM PRESSURIZED Light is lit when air
pressure is supplied to the system; the light is
extinguished when the air supply is depressurized.
This occurs after the PUMP ON Pushbutton has
been pushed and the Pumps turned on.

•

PUMP ACTIVE Light is lit when the air supply is
turned on to the Pumps; the light is extinguished
when the Pumps are inactive, thus turned off. This
is activated by the PUMP ON Pushbutton.

•

AIR PRESS ON Light is lit when air pressure to the
system is turned on; the light is extinguished when
air pressure to the system is shutoff.

•

RAM READY Light is lit when the drum is in
position; the light is extinguished when the drum is
not in position.

•

PUMP READY Light is lit when the Pumps are
primed and ready for operation; the light is
extinguished when the Pumps are not ready for
operation.

•

PRIME PUMP Pushbutton turns on the Pumps, for
priming. When the Pumps are primed, the PUMP
READY Light turns on. The switch is not used when
the PUMP READY Light is lit. The PUMP ACTIVE
Light will blink.

•

PUMP RESET Pushbutton resets the Pumps to an
active state. When the Pumps are reset, the PUMP
ACTIVE Light turns off. The switch is not used when
the PUMP ACTIVE Light is lit. The PUMP READY
Light is on.

•

PUMP ON Pushbutton turns the Pumps on and off.
When the Pumps are turned on, the PUMP ACTIVE
Light also turns on. When the Pumps are turned off,
the PUMP ACTIVE Light also turns off.

•

BULK SUPPLY DEPRESSURIZATION Pushbutton
opens the depressurization valve to lower the fluid
pressure.

•

LOCAL REMOTE Switch puts the system into or out
of automatic operation.

«
...
17
18
19
20
21
...
»

Содержание 309028ZAT



































































































Отзывы:

Нет отзывов

Похожие инструкции для 309028ZAT

Бренд: Nabtesco Страницы: 26

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Yamaha Страницы: 45

Бренд: ZOLL Страницы: 48

Бренд: A.J.Antunes Страницы: 24

Бренд: B&G Страницы: 2

Бренд: JBL Страницы: 17

FLOOReco 5164-040120

Бренд: DOTLUX Страницы: 10

Бренд: Griven Страницы: 36

Бренд: Metrohm Страницы: 42

Бренд: Maquet Страницы: 232

KONTROL KUBE ABACUS

Бренд: FIBERLOCK Страницы: 8

Бренд: Monosem Страницы: 92

Бренд: Otto Bock Страницы: 252

Бренд: Original BTC Страницы: 2

Бренд: ResMed Страницы: 8

Бренд: ZOLL Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды