Graco 309028ZAT Скачать руководство пользователя страница 35

Страница: 35 / 98

Pressure Relief Procedures

309028ZAT

Pneumatic Pressure Relief
Procedure

This procedure describes how to relieve pressure on the
Pneumatic Logic Panel (G) and cylinders. Use this
procedure whenever you perform ram assembly service
on the piston rod seal or the ram piston.

1. Follow

Fluid Pressure Relief Procedure

on page

34.

2. Fully lower the ram by setting the RAM POSITION

Switch (AG) to LOWER. Leave the switch in the
LOWER position.

3. Open the door on the Pneumatic Logic Panel (G).

4. Adjust the air pressure to 0 PSI for the RAM DOWN

Air Regulator (AK). Refer to the gauge on the RAM
DOWN Air Regulator (AK) and R3 Regulator (AL) to
verify the ram has been depressurized. See F

. 17.

5. Slowly open the drain cock located on the bottom of

the air cylinders (CL).

6. After the air pressure has been relieved, remove the

Ram Down air line running from the top of the
Pneumatic Logic Panel (G) to the ram cross bar
(CB).

7. Close the Main Air Shutoff Valve (P) on header.

8. Leave the drain cock open and the Ram Down

airline removed until service is complete.

9. After service is complete, close drain cocks and

make all pneumatic connections and open the Main
Air Shutoff Valve (P) to header. Perform the

Adjusting the RAM UP and RAM DOWN Air
Regulators

procedure, page 30.

. 16

. 17

Содержание 309028ZAT



































































































Результаты поиска

Содержание 309028ZAT

Отзывы:

Похожие инструкции для 309028ZAT

Бренды по названию

Популярные бренды

Graco 309028ZAT, Инструкция по эксплуатации

Результаты поиска

Содержание 309028ZAT

Отзывы:

Похожие инструкции для 309028ZAT

Бренды по названию

Популярные бренды