Graco 309028ZAT Скачать руководство пользователя страница 17

Страница: 17 / 98

Component Identification

309028ZAT

Junction Box Panel Switches and Indicators

Use the table and F

. 6 when operating the switches and reading the indicator on the Junction Box Panel.

Button/Switch

What it Does

PRIME PUMP Pushbutton

• Primes both displacement Pumps with material, making the

Pumps ready to operate.

• Lights PUMP READY Light.

PUMP RESET Pushbutton

• Restarts the Pumps after the Pumps were turned off.
• Lights PUMP ACTIVE Light

PUMP ON Pushbutton

• Activates the Pumps.
• Deactivates the Pumps.

BULK SUPPLY
DEPRESSURIZATION Pushbutton

• Opens the depressurization valve to lower the fluid supply

pressure.

LOCAL REMOTE Switch

• Places fluid dispensing system into Automatic or Manual mode.

Indicator

Indicator
Light is

Meaning

SYSTEM
PRESSURIZED Light

System is pressurized.

OFF

System is depressurized.

PUMP ACTIVE Light

Pumps are active; air is available to the Pumps.

OFF

Pumps are inactive; air is unavailable to the Pumps.

AIR PRESS ON Light

Air pressure is available to the Pumps for use.

OFF

Air pressure is not available to the Pumps for use.

RAM READY Light

Follower Plate (D) is ready for use.

OFF

Follower Plate (D) is not ready for use.

PUMP READY Light

Pumps are primed and ready to use.

OFF

Pumps are not ready to use.

Содержание 309028ZAT



































































































Результаты поиска

Содержание 309028ZAT

Отзывы:

Похожие инструкции для 309028ZAT

Бренды по названию

Популярные бренды

Graco 309028ZAT, Инструкция по эксплуатации

Результаты поиска

Содержание 309028ZAT

Отзывы:

Похожие инструкции для 309028ZAT

Бренды по названию

Популярные бренды