Graco 309028ZAT Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 98

background image

Installation

309028ZAT

21

Installing the Uni-Drum

To install the Uni-Drum, follow the procedure below.
Refer to

Technical Specifications

on page 94 for ram

mounting and clearance dimensions.

1. Using equipment such as a forklift or handtruck,

move the Uni-Drum into place on the floor. Remove
the shipping pallet.

2. Level the Uni-Drum, using metal shims.

3. Using the holes in the base as a guide, drill holes for

13 mm (1/2 in.) anchors.

4. Bolt the Uni-Drum to the floor using anchors that are

long enough to prevent the unit from tipping.

Installing Drum Clamps

NOTE:

Drum Clamps (K) are only used with 25N914

and 25N915 Uni-Drum models. See

Identification

Two Drum Clamps (K) are provided with the system to
be installed prior to system operation. The clamps hold
the drum in place while removing the Follower Plate (D).
The end user must locate and install the clamps in a
manner that will hold the drum to the frame evenly.

Installing Drum In Position
Switch

NOTE:

The Drum in Position Switch (L) is only used

with 25N914 and 25N915 Uni-Drum models. See

Component Identification

A Drum In Position Switch (L) is provided with the
system to be installed prior to system operation. The
Drum in Position Switch indicates that the drum is
loaded. The end user must locate and install the switch
in a location that will indicate the drum is in position.
Connect the switch as shown below to the Pneumatic
Logic Panel (G).

F

IG

. 7: Uni-Drum Supply Switch

Connect to

“Drum in position

signal”

Connect to
”Drum in position
supply port”

«
...
19
20
21
22
23
...
»

Содержание 309028ZAT



































































































Отзывы:

Нет отзывов

Похожие инструкции для 309028ZAT

Бренд: Cadman Страницы: 66

Бренд: Facnor Страницы: 33

Бренд: Hammer Страницы: 42

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Aspect Q-CARD 100-4T

Бренд: idi Страницы: 38

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: ABB Страницы: 112

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

Бренд: SDE Lighting Страницы: 7

Бренд: MacDon Страницы: 558

Бренд: GYM form Страницы: 40

Бренд: Cameo Страницы: 188

Бренд: Calex Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды