Graco 309028ZAT Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 98

background image

PLC Interface Accessory Kit Service

42

309028ZAT

PLC Interface Accessory Kit Service

Valve Assembly Bank

Remove the valve assembly bank that is mounted below
the Junction Box Panel (H) as follows:

NOTE:

The valve assembly bank has two solenoids

(SOL139 and SOL147) that are used as switches to
control Pump operation. SOL139 depressurizes the
Pumps. If the output is high (open), Pumps will
depressurize. SOL147 turns air on to the Pumps.

1. Shut off power to the Junction Box Panel (H).

Valve Assembly Removal

2. Remove the cover off the Junction Box Panel (H).

3. Locate the valve assembly (203) that is attached to the

mounting plate (201) below the Junction Box Panel
(217). See F

4. Disconnect the two cables (216) from the terminal strip

inside the Junction Box Panel (217) for the valve
assembly (203) bank. For wiring information, refer to
the

Electrical Diagram

5. Remove four cap screws (205), the lock washers

(206), and the valve assembly (203) from the
mounting plate (201).

Valve Assembly Replacement

6. Install the new valve assembly (203) on the mounting

plate (201) using the four cap screws (205) and lock
washers (206). See F

7. Reconnect the two cables (216) on the terminal strip

inside the Junction Box Panel (217) for the valve
assembly (203) bank. For wiring information, refer to
the

Electrical Diagram

8. Reinstall the cover on the Junction Box Panel (H).

9. Reapply power to the Junction Box Panel (H).

10. Perform the

Daily System Startup

procedure on

at the applicable Supply Unit (LH or RH).

11. Verify that the valve assembly (203) bank operates

correctly.

12. Return the system to previous operation settings.

Pressure Switch Assembly
Replacement

Remove the pressure switch assembly that is mounted
below the Junction Box Panel (H) as follows:

NOTE:

The pressure switch (PS108) turns air pressure

on the system.

1. Shut off power to the Junction Box Panel (H).

Switch Removal

2. Remove the cover from the Junction Box Panel (H).

3. Locate the pressure switch assembly (202) that is

attached to the mounting plate (201) below the
Junction Box Panel (217). See F

4. Disconnect the 5-pin cord (211) from the pressure

switch assembly (202). For wiring information, refer to
the

Electrical Diagram

on page 91.

5. Disconnect the end of the lead wire from the pressure

switch assembly (202). Leave the other end of the
lead wire connected to the valve assembly bank (203).

All electrical wiring must be done by a qualified
electrician and comply with all local codes and
regulations.
Installing and servicing this equipment requires
access to parts which could cause an electric shock
or other serious injury. Have only qualified electricians
access the control assembly.

All electrical wiring must be done by a qualified
electrician and comply with all local codes and
regulations.
Installing and servicing this equipment requires
access to parts which could cause an electric shock
or other serious injury. Have only qualified electricians
access the control assembly.

«
...
40
41
42
43
44
...
»

Содержание 309028ZAT



































































































Отзывы:

Нет отзывов

Похожие инструкции для 309028ZAT

Бренд: ABB Страницы: 14

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: FENDT Страницы: 31

Бренд: Campbell Страницы: 2

Бренд: Jaga Страницы: 32

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: V-TAC Страницы: 13

Бренд: Posture Pump Страницы: 2

Бренд: Warner Electric Страницы: 14

Бренд: Bowa Страницы: 140

Бренд: Toparc Страницы: 32

Бренд: ASIA TECHNOLOGY Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды