manualshive.com logo in svg

Gossen MetraWatt PROFITEST 204, Руководство по эксплуатации, Страница: 9 / 76

Поделиться
Скачать
Gossen MetraWatt PROFITEST 204 Скачать руководство пользователя страница 9

GMC-I Messtechnik GmbH

9

2

Safety Features and Precautions

This instrument fulfills the requirements of the applicable Euro-
pean and national EC guidelines. We confirm this with the CE 
marking. The relevant declaration of conformity can be obtained 
from GMC-I Messtechnik GmbH.

The 

PROFITEST 204+

, 204 HP and 204 HV test instruments have 

been manufactured and tested in accordance with the following 
safety regulations:

IEC 61010-1 / DIN EN 61010-1 / VDE 0411-1, 
DIN VDE 0413, part 1, and EN 60204 / DIN VDE 0113

If used for their intended purpose, the safety of the user, the 
instrument and the device under test is assured.

Read the operating instructions thoroughly and carefully before using 
your instrument, and follow all instructions included therein. 
Make sure that the operating instructions are readily available to all oper-
ators.

Observe the following safety precautions:

• The instrument may only be connected to electrical supply 

systems with 230 V/240 V which conform to the valid safety 
regulations (e.g. IEC 60364, VDE 0100) and are protected with 
a fuse or circuit breaker with a maximum rating of 16 A. 

• Be prepared for the occurrence of unexpected voltages at 

devices under test (for example, capacitors may be 
dangerously charged).

• Make certain that connector cables, measurement cables and 

test cables are in flawless condition, e.g. no damage to 
insulation, no interruptions in cables or plugs, no kinks etc

.

• Impulse withstand voltages of up to 2.5 kV may occur in 

overvoltage category II systems with 230/400 V.

The PROFITEST 204+ basic instrument and the PROFITEST 204HP and HV 
high-voltage modules may not be operated:

• If visible damage is apparent
• If connector, measuring or test cables are damaged 
• If they no longer function correctly
• If the signal lamps are defective
• If the functions test is not passed (see chapter 4.5.1, page 35)
In such cases, the instrument must be removed from service and 
secured against unintentional use. Send the instrument to the 
Repair and Replacement Parts Service Department (see chapter 13).

Opening of Equipment / Repair

The equipment may be opened only by authorized service per-
sonnel to ensure the safe and correct operation of the equipment 
and to keep the warranty valid. Even original spare parts may be 
installed only by authorized service personnel. 
In case the equipment was opened by unauthorized personnel, 
no warranty regarding personal safety, measurement accuracy, 
conformity with applicable safety measures or any consequential 
damage is granted by the manufacturer.

Data Backup

The measurement, report and input data are stored and secured 
in the test instrument RAM as long as the associated battery sup-
plies the required voltage. Please note that the data will be lost 
during a software update. We therefore advise you to regularly 
transmit your stored data to a PC in order to prevent potential loss 
of data in the test instrument. We assume no responsibility for any 
data loss. For data processing and management we recommend 
the following PC software programs:

• ETC

•

PS3

 (documentation, management, report generation and

monitoring of deadlines)

•

PC.doc-WORD™/EXCEL™ 

(report and list generation)

•

PC.doc-ACCESS™

 (test data management)

•

ELEKTROmanager

 for 

PROFITEST 204+

Содержание PROFITEST 204













































































Отзывы:

Нет отзывов