Fryer Components and Their Function
3 - 2 Lower Cabinet Area
ITEM
DESCRIPTION
FUNCTION
1.
Fig. 2
Filter Pan Hold-Down Bracket
The Hold-Down Bracket is contained in the Filter Pan
and Latches
and serves to ensure the filter paper is held
tightly in place by means of the four locking latches.
The fryer’s filtering action will be reduced or eliminat-
ed if these latches are not properly secured.
2.
Fig. 2
T-Handle/Drain Valve
Turning this T-Handle counter-clockwise allows
shortening to drain from the frying vessel into the
Filter Pan.
Open the valve slowly to avoid burns
from splashing of hot oil.
Always ensure the valve
is closed prior to adding shortening.
Your fryer will
not operate if this drain valve is not completely
closed. (i.e., clockwise)
3.
Fig. 2
Drain Valve Pipe-Drain
This Pipe-Drain attaches to the drain valve and helps
to minimize splashing of hot oil when the fry-kettle is
filtered or drained. The Pipe-Drain must be removed
before sliding the Filter Pan out of the fryer.
Always
use insulted gloves to remove this hand
tightened pipe.
4.
Fig 2
Quick Disconnect for Oil
This Quick-Disconnect Fitting is used in conjunction
Discharge Wand
with the oil discharge wand to remove oil from the
fryer that is to be discharged.
5.
Fig 2
Diverter Valve
The Diverter Valve may be identified by its colored
lever-type handle. During a normal operation it
should be positioned so it points outward toward
the operator. For removal of oil with the discharge
hose connected, the Diverter Valve handle should be
turned inward and counter-clockwise. After removal
of oil for discard it should be returned to its normal
position pointing toward the operator. Details of the
oil procedure are covered in the operations of this
manual.
6.
Fig 2
Quick Disconnect For Filter Pan
This Quick Disconnect fitting serves to connect the
hose from the Filter Pan to the fryer’s oil return lines.
The hose must be disconnected at this fitting prior to
sliding the Filter Pan outward for cleaning or removal.
The fitting is operated by pushing upward on the
insulating ring and exerting downward pressure on
the connecting end of the hose. For reconnection,
push upward on the insulating ring while inserting
the hose. Release the insulating ring when the hose
fitting is fully inserted to lock it in position.
10
Содержание Chester Fried CF 400
