GHM 607132 страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 34

background image

E44.X.01.6C-04

Mounting- and Operating Manual GIR 300

page 31 of 34

- Sensor broken (thermo-elements)

Remedies:

- Check sensor or exchange defective sensor

Er.11

Value could not be calculated

Indicates a measuring value, needed for calculation of the display value, is faulty or out of range.

Possible causes:

- Incorrect scale

Remedies:

- Check settings and input signal

12 Decommissioning, reshipment and disposal

12.1 Decommissioning

Always disconnect the device before from its supply before decommission (e.g. at fuse). Valid general
safety requirements shall be observed.

Please also make sure that connected Loads are disconnected also and are in a safe state.

12.2 Reshipment and disposal

All devices returned to the manufacturer have to be free of any residual of measuring
media and other hazardous substances.
Measuring residuals at housing or sensor may be a risk for persons or environment

Use an adequate transport package for reshipment, especially for fully functional de-
vices. Please make sure that the device is protected in the package by enough pack-
ing materials.

Add the completed reshipment form of the GHM website

http://www.ghm-messtechnik.de/downloads/ghm-formulare.html

.

The device must not be disposed in the unsorted municipal waste! Send the device
directly to us (sufficiently stamped), considering the above if it should be disposed.
We will dispose the device appropriate and environmentally sound

«
...
29
30
31
32
33
...
»

Содержание 607132



































Отзывы:

Нет отзывов

Похожие инструкции для 607132

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: zipwake Страницы: 12

Бренд: Watts Страницы: 2

Бренд: jbc Страницы: 12

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: Haier Страницы: 58

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Abocom Страницы: 10

Бренд: ZPA Pecky, a.s. Страницы: 36

VEGACAP 60 Series

Бренд: Vega Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды