manualshive.com logo in svg

Gestetner A294, Руководство по обслуживанию

Поделиться
Скачать
Gestetner A294 Скачать руководство пользователя страница 476

SERVICE CALL CONDITIONS

Rev. 9/2001

A294/A295

7-18

SM

SC441: Development Motor Lock

Definition [B]

The development motor lock signal is longer than 2 seconds while the
development motor is on.

Possible Causes

•

 Too much load on the drive mechanism

•

 Development motor defective

•

 Poor development motor connector connection

•

 BCU defective

SC491: Polygonal Mirror Motor Cooling Fan Motor Lock

Definition [B]

The polygonal mirror motor cooling fan

 

motor lock signal is longer than 5

seconds while the polygonal mirror motor cooling fan motor is on.

Possible Causes

•

 Too much load on the drive mechanism

•

 Polygonal mirror motor cooling fan motor defective

SC495: Toner Bottle Unit Error

Definition [B]

The toner hopper sensor cannot detect toner even if the toner supply coil clutch
turns on for 2 seconds x 10 times during toner supply during copying.

Possible Causes

•

 Toner supply motor defective

•

 Toner supply coil clutch defective

•

 Toner supply motor connector connection

•

 Toner supply coil clutch connector connection

•

 Toner near-end sensor (in the toner bank) defective

•

 Toner hopper sensor defective

•

 Toner clogged in the supply system

SC496: Toner Collection Bottle Error

Definition [B]

The used toner collection bottle or sucked toner collection bottle sensor
remains off for 3 seconds.

Possible Causes

•

 Used toner collection bottle or sucked toner collection bottle is incorrectly set

•

 Used toner collection bottle or sucked toner collection bottle connector is

loose or sensor defective

CÓPIA NÃO CONTROLADA

CÓPIA NÃO CONTROLADA

Содержание A294

























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды