Gestetner A294 Скачать руководство пользователя страница 41

Страница: 41 / 600

ELECTRICAL COMPONENT DESCRIPTIONS

1-13

A294/A295

erall

Inf

rmat

ion

1.7 ELECTRICAL COMPONENT DESCRIPTIONS

Refer to the electrical component layout in the plastic pouch for the location of the
components using the symbols and index numbers.

1.7.1 COPIER ENGINE

Symbol

Name

Function

Motors

Scanner

Drives the 1st and 2nd scanners.

Polygonal Mirror

Turns the polygonal mirror.

Drum

Drives the drum, cleaning unit, and transfer belt unit.

Development

Drives the development unit.

Toner Supply

Supplies the toner to the toner hopper.

Toner Bank

Drives the toner transport coil, which feeds fresh
toner from the toner bank to the toner supply cylinder.

Upper Toner Bottle

Rotates the upper toner bottle to supply toner to the
toner entrance tank.

Upper Bottle Cap

Opens and closes the inner cap of the upper toner
bottle.

Lower Toner Bottle

Rotates the lower toner bottle to supply toner to the
toner entrance tank.

M10

Lower Bottle Cap

Opens and closes the inner cap of the lower toner
bottle.

M11

Charge Corona Wire
Cleaner

Drives the charge corona wire cleaner.

M12

Fusing/Duplex

Drives the fusing unit, duplex unit, inverter unit, and
paper exit rollers.

M13

Paper Feed

Drives the paper feed, separation, pick-up, lower
relay, and vertical transport rollers.

M14

Relay

Drives the upper relay roller and the LCT relay roller.

M15

1st Tray Lift

Raises and lowers the bottom plate in the 1st paper
tray.

M16

2nd Tray Lift

Raises and lowers the bottom plate in the 2nd paper
tray.

M17

3rd Tray Lift

Raises and lowers the bottom plate in the 3rd paper
tray.

M18

Registration

Drives the registration rollers.

M19

Oil Supply/Cleaning
Web

Drives the oil supply/cleaning web.

M20

Rear Fence Drive

Moves the paper stack in the left tandem tray to the
right tandem tray.

M21

Jogger

Drives the jogger fences to square the paper stack in
the duplex unit.

M22

Optics Cooling Fan

Removes heat from the scanner optics unit.

M23

Polygonal Mirror
Motor Cooling Fan

Removes heat from around the polygonal mirror
motor.

M24

LDB Cooling Fan

Removes heat from around the LDB.

CÓPIA NÃO CONTROLADA

Содержание A294

























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание A294

Отзывы:

Похожие инструкции для A294

Бренды по названию

Популярные бренды

Gestetner A294, Руководство по обслуживанию

Результаты поиска

Содержание A294

Отзывы:

Похожие инструкции для A294

Бренды по названию

Популярные бренды