Gestetner A294 Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 600

Gestetner A294 Скачать руководство пользователя страница 225

Rev. 9/2001

GENERAL CAUTIONS

SM

4-3

A294/A295

Serv

ic

e

Ta

b

le

s

4.1.6 CHARGE CORONA

1. Clean the corona wires with a dry cloth. Do not use sandpaper or solvent.

2. Clean the charge corona casing with water first to remove NOx based

compounds. Then clean it with alcohol if any toner still remains on the casing.

3. Clean the end block with a blower brush first to remove toner and paper dust.

Then clean with alcohol if any toner still remains.

4. Do not touch the corona wires with bare hands. Oil stains from fingers may

cause uneven image density on copies.

5. Make sure that the wires are correctly between the cleaner pads and that there

is no foreign material (iron filings, etc.) on the casing.

6. When installing new corona wires, do not bend or scratch the wire surface.

Doing so may cause uneven charge. Also be sure that the corona wires are
correctly positioned in the end blocks. (See Charge Corona Wire Replacement)

7. Clean the grid plate with a blower brush (not with a dry cloth).

8. Do not touch the charge grid plate with bare hands. Also, do not bend the

charge grid plate or make any dent in it. Doing so may cause uneven charge.

4.1.7 DEVELOPMENT

1. Be careful not to nick or scratch the development roller.

2. Place the development unit on a sheet of paper after removing it from the

copier.

3. Never disassemble the development roller assembly. The position of the doctor

plate is set with special tools and instruments at the factory to ensure the
proper gap between the doctor blade and the development roller.

4. Clean the drive gears after removing used developer.

5. Dispose of used developer in accordance with local regulations.

6. Never load types of developer and toner into the development unit other than

specified for this model. Doing so will cause poor copy quality and toner
scattering.

7. Immediately after installing new developer, the TD sensor initial setting

procedure should be performed to avoid damage to the copier. Do not perform
the TD sensor initial setting with used developer. Do not make any copies
before doing the TD sensor initial setting.

8. When using a vacuum cleaner to clean the development unit casing, always

ground the casing with your fingers to avoid damaging the toner density sensor
with static electricity.

9. When replacing the TD sensor, the developer should be replaced and then the

TD sensor initial setting procedure (SP2-801) should be done, followed by
process control initialization (SP2-962).

CÓPIA NÃO CONTROLADA

CÓPIA NÃO CONTROLADA

«
...
223
224
225
226
227
...
»

Содержание A294

























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды