Genie GCL-J&H 1/2HP Скачать руководство пользователя страница 18

Страница: 18 / 68

4.7

www.geniecompany.com

01-14

1) Route the hand chain through the chain guide, around the

pocket wheel and back through the chain guide. Fig. 8.

2) Connect the hand chain ends together as shown in Fig 9.

by twisting open the last link on one end of the chain, and

slipping the last link on the opposite end onto the open link.

3) Twist open link closed again.

4) Mount chain keeper to wall in line with chain approximately

4 feet from floor.

5) Loop chain around keeper as shown. Fig. 10. Optional Padlock

not provided.

6) Install hoist cable.

• With operator installed motor DOWN, attach hoist cable to

cam arm hole closest to mounting plate. Fig. 11.

• With operator installed motor UP, attach hoist cable to cam

arm hole closest to electric box. Fig. 11.

Hand Chain and Keeper

Figure 9

Figure 10

NOTE: To insure smooth operation, make sure there is no twist in the

hand chain before connecting the link ends together.

MOUNTED

MOTOR UP

MOUNTED

MOTOR DOWN

ATTACH

HOIST

CABLE

HERE

Figure 11

ATTACH

HOIST

CABLE

HERE

Figure 8

Содержание GCL-J&H 1/2HP





































































Результаты поиска

Содержание GCL-J&H 1/2HP

Отзывы:

Похожие инструкции для GCL-J&H 1/2HP

Бренды по названию

Популярные бренды

Genie GCL-J&H 1/2HP, Руководство по установке

Результаты поиска

Содержание GCL-J&H 1/2HP

Отзывы:

Похожие инструкции для GCL-J&H 1/2HP

Бренды по названию

Популярные бренды