Generac Mobile MDE570P Скачать руководство пользователя страница 29

Страница: 29 / 80

Owner’s Manual for Mobile Generator

Cold Weather Starting Aids (If

Equipped)

Component Locations

See

Figure 2-24

. This unit may be equipped with one or

starting

aids

for

cold

weather

operation.

Figure 2-24. Parts Removed for Clarity

(A) Oil Pan Heater

1,000 W, 120 VAC. Requires optional shore power inlet

(see receptacle panel).

(B) Block Heater

2,250 W, 120 VAC. Requires optional shore power inlet

(see receptacle panel).

(C) Fuel Filter Heaters (×3)

50 W, 24 VDC.

(D) Crankcase Ventilation Heater

54 W, 24 VDC.

(E) 30 A Battery Charger

Requires optional shore power inlet (see receptacle

panel). See

Operation

for more information.

(F) 1,100 CCA Batteries

More cranking power for extreme cold.

(Not Shown) 60/40 Coolant

60% ethylene glycol mixture lowers freezing point of

coolant.

Recommendations

IMPORTANT NOTE: The use of correct grade oil is

critical to achieving adequate cold weather cranking

speed. Synthetic oils have improved flow at low tem

peratures. see

Engine Oil Recommendations

Starting aids may be required under the following

conditions:

•

Cold weather.

•

When starting equipment with high parasitic loads

during cranking and start acceleration to idle.

•

When using unit above 5,000 ft (1,500 m) altitude.

See

Figure 2-25

. Recommended cold-weather packages

vary in accordance with expected temperatures.

Figure 2-25. Recommended Packages

(A) From 32 to 0 °F (0 to -18 °C)

Standard Package is recommended.

(B) From 32 to -40 °F (0 to -40 °C)

Extreme Package is recommended.

Left Side

Right Side

014039

(000583)

DANGER

Explosion. Do not use ether when starting an
engine equipped with glow plugs or an air intake
heater. Doing so could cause an explosion, which
will result in death or serious injury.

014040

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 29 / 80

Результаты поиска

Содержание MDE570P

Отзывы: