Generac Mobile MDE570P Скачать руководство пользователя страница 59

Страница: 59 / 80

Owner’s Manual for Mobile Generator

Section 5: Troubleshooting

General Troubleshooting

This information is intended to be a check or verification

for simple causes that can be located and fixed. It does

not cover all types of problems. See the OEM engine

manual for additional troubleshooting information.

Procedures that require in-depth knowledge or skills

should be performed by a GMASD.

Problem

Possible Causes

Solution

Low fuel level shut

down

Low fuel level

Check fuel level on controller.

Unit not level

Verify unit is sitting level to ensure an accurate reading.

Leaking fuel tank

Check tank for leaks.

Damaged fuel sender or

wiring

Check for continuity between sender and engine controller.

Low oil pressure shut

down

Low oil level

Check oil level on dipstick. Add oil if necessary.

Leaking oil from engine

Visually inspect the engine for leaks. Restart unit and verify loss

of pressure. Immediately stop engine if pressure does not reach

5 psi (34.5 kPa) within five seconds.

Oil pressure sender

See the OEM engine manual to identify corrective action.

Low coolant level

shutdown

Low coolant level

Allow engine to cool, then check coolant level in radiator. Add

coolant if necessary.

Leaking coolant hoses

Inspect hoses for leaks. Repair or replace as necessary.

Leaking engine block or

water pump

Visually inspect for leaks. Verify no coolant has mixed with the

engine oil (oil will appear milky). See the OEM engine manual

for additional information.

High coolant tem

perature shutdown

Low coolant level

Add coolant if necessary. Allow engine to cool, then check cool

ant level in radiator. Restart engine and check coolant tempera

ture (on controller). Immediately stop engine if coolant

temperature is 210 °F (99 °C) or higher.

Blockage in radiator

Check radiator shroud and ducting for blockage and remove

any foreign matter.

Leakage in coolant

hoses, engine block, or

water pump

• Inspect for visible leaks. Check tension of water pump

serpentine drive belt.

• Remove load on generator and restart engine. Check

coolant temperature and immediately stop engine if it

starts to overheat. See the OEM engine manual for addi

tional information on engine overheating.

Overcrank shutdown

Fuel level low

• Check fuel level in tank.
• Check fuel pump operation.
• Check air filter for blockage.
• See the OEM engine manual for additional information.

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 59 / 80

Результаты поиска

Содержание MDE570P

Отзывы: