Generac Mobile MDE570P Скачать руководство пользователя страница 36

Страница: 36 / 80

Owner’s Manual for Mobile Generator

Figure 3-8. Mode Buttons

Fine Tuning the Voltage

Voltage adjustment range is ±10%. This can be done

when engine is running and breaker is closed to fine tune

voltage output at load connection.

IMPORTANT NOTE: This procedure is only permit

ted on non-parallel capable machines. Machines set

up with parallel controls will not respond to voltage

adjustments when the breaker is closed.

See

Figure 3-9

. Use the controller navigation buttons to

fine-tune generator output voltage.

Figure 3-9. Navigation Buttons

From the Home page, press and hold the CHECK

MARK button (A) to access the Running configura

tion editor - display.

Press the UP or DOWN button to scroll to the Edi

tor - Generator Voltage Adjust L-N page.

Press and release the CHECKMARK button so the

voltage starts to flash.

Press the UP or DOWN button to change voltage.

Press and release the CHECKMARK button to set

and save the voltage setting. The value stops

flashing.

NOTE:

•

The new voltage setting is retained through ON-

OFF cycles of the generator.

•

When battery power is cycled through the battery

disconnect switch, the voltage setting returns to the

target voltage for which the link board is

configured.

Press and hold the CHECKMARK button to exit the

Running configuration editor.

Voltage Regulator

The voltage regulator controls the output of the generator

by regulating current into the exciter field. The voltage

regulator is adjusted before shipment from the factory

and typically does not require adjustment.

Main Circuit Breaker

See

Figure 3-10

. The main circuit breaker is on the unit

backside, between the control panel and AC distribution

panel.

Figure 3-10. Main Circuit Breaker

When the main line circuit breaker (MLCB) is OFF (O),

power is interrupted to the connection lugs and the

optional cam lock receptacles. The breaker may be

switched ON (I) after connections have been made to the

connection lugs or the optional cam lock receptacles, and

the unit has been started and allowed to reach normal

operating speed and temperature.
The convenience receptacles have separate circuit

breakers protecting those circuits and operate

independent from the MLCB. If the MLCB is switched off,

the convenience receptacles may still provide power.

Verify the 20/50 A circuit breakers for their respective

circuits.
Any of the following conditions can trip the main circuit

breaker:

•

Overload of the generator circuits to the connection

lugs or the optional cam lock receptacles.

•

The door covering the connection lugs is open.

A STOP Mode button
B MANUAL Mode button
C AUTO Mode button

010417

010418

014017

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 36 / 80

Результаты поиска

Содержание MDE570P

Отзывы: