Generac Mobile MDE570P Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 80

Generac Mobile MDE570P Скачать руководство пользователя страница 7

Owner’s Manual for Mobile Generator

3

Electrical Hazards

Lifting Hazards

Explosion and Fire Hazards

(000145)

DANGER

Electrocution. In the event of electrical accident,
immediately shut power OFF. Use non-conductive
implements to free victim from live conductor. Apply
first aid and get medical help. Failure to do so will
result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power
source, if not avoided, will result in death
or serious injury.

(000144)

DANGER

Electrocution. Contact with bare wires,
terminals, and connections while generator
is running will result in death or serious injury.

(000152)

DANGER

Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.

(000123)

DANGER

Electrocution. Turn utility supply OFF before
working on utility connections of the transfer
switch. Failure to do so will result in death or
serious injury.

(000150)

Electrocution. Never connect this unit to the electrical
system of any building unless a licensed electrician
has installed an approved transfer switch. Failure to
do so will result in death or serious injury.

DANGER

(000164)

WARNING

Electrical shock. Disconnect battery ground
terminal before working on battery or battery
wires. Failure to do so could result in death
or serious injury.

Personal injury. Failure to properly connect
lifting cables, chains, or straps could result in
death, serious injury, or property damage.

(000346)

WARNING

WARNING

(000349)

Personal Injury. Do not use lifting hook if there are
signs of damage or corrosion. Doing so could result
in death, serious injury, or property damage.

(000350)

WARNING

Personal Injury. Do not use lifting hook other than
as directed. Failure to do so could result in death,
serious injury, or property damage.

(000351)

Personal Injury. Verify all fasteners are properly
tightened prior to lifting unit. Failure to do so could
result in death, serious injury, or property damage.

WARNING

(000105)

Explosion and Fire. Fuel and vapors are extremely
flammable and explosive. Add fuel in a well
ventilated area. Keep fire and spark away. Failure
to do so will result in death or serious injury.

DANGER

WARNING

(000281)

Fire risk. Fuel and vapors are extremely
flammable. Do not operate indoors. Doing
so could result in death, serious injury, or
property or equipment damage.

(000147)

WARNING

Risk of Fire. Unit must be positioned in a
manner that prevents combustible material
accumulation underneath. Failure to do so
could result in death or serious injury.

«
...
5
6
7
8
9
...
»

Содержание MDE570P

















































































Отзывы:

Нет отзывов