Generac Mobile MDE570P Скачать руководство пользователя страница 27

Страница: 27 / 80

Owner’s Manual for Mobile Generator

Fuel System

Standard units are equipped with the following fuel sys

tem components:

•

Single wall fuel tank

•

Engine fluid containment

•

Engine fluid containment sensor

Fuel Tank

See

Figure 2-21

for fuel tank components.

Figure 2-21. Fuel Tank

Engine Aftertreatment Monitoring

This section describes the indicators that display on the

After Treatment Status page of the Engine tab.

Figure 2-22

. This unit is equipped with an exhaust gas

recirculation cooler (EGR), diesel oxidation catalyst

(DOC), diesel particulate filter (DPF), and selective

catalyst reduction system (SCR), to meet Tier 4 Final

EPA emissions standards.

Figure 2-22. Aftertreatment System

To access the After Treatment Status status page:

Press an arrow button (▲, ►, ▼, or ◄) to access

the Maintenance pages.

When on the Engine tab, press ▼ to scroll through

the pages until the After Treatment Status page

displays.

Four areas of the After Treatment Status page

communicate information to the operator. The areas and

the indicators that appear in those areas are explained

here:

•

HEST

Lamp

(High

Exhaust

System

Temperature):

This area displays the regeneration

underway indicator above the words HEST LAMP -

SOLID when the unit is in the process of the

exhaust catalyst. During the regeneration process,

the exhaust temperature will be very high.

•

DPF Regeneration Lamps:

Depending upon the

Engine Type selected in the module’s

configuration, the Engine section may include the

DPF Regeneration Lamps page. This page

contains icons to show the status of various ECU

functions, some of which are applicable to Tier 4

engine requirements. The icons flash at different

rates to show the status of the ECU function, refer

to the engine manufacturer for more information

about this.

Single-wall or double-wall fuel tank

Auxiliary fuel tank connection (if equipped)

Engine fluids (oil, coolant, and DEF) leak detection

sensor

Fuel leak detection sensor (Rupture basin alarm) (if

equipped)

Fuel level sender

Fuel supply

Fuel return

01400

SCR module

Spark plug for after burner system

DOC and DPF

01403

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 27 / 80

Результаты поиска

Содержание MDE570P

Отзывы: