Generac Mobile MDE570P Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 80

Generac Mobile MDE570P Скачать руководство пользователя страница 38

34

Owner’s Manual for Mobile Generator

Figure 3-12. Grounding Lug

Cam Lock Connections (If Equipped)

See

Figure 3-13

. The unit may be equipped with cam

lock connections. If equipped, they are on the unit

backside, below the connection lugs.

Figure 3-13. Cam Lock Panel

Cam locks provide connection points to attach external

loads to the generator.
Above the connection lugs, decals describe the cam

locks. Also, cam locks are color-coded, according to

country of destination.

IMPORTANT NOTE: The nation for which the unit is

configured determines cam lock colors, and decals

indicate which color convention is being followed.

Connections should be made by plugging power cables

equipped with series 16 taper nose 400 A, 600 V cam

lock plugs into the cam lock receptacles.

Secure

connection by rotating plug one-half turn to the right.

014047

A

(000156)

DANGER

Electrocution. Before connections are made to
the unit, verify the main circuit breaker and
battery disconnect switch are OFF. Failure to do
so will result in death or serious injury.

(000237)

DANGER

Electrical backfeed. Use only approved switchgear to
isolate generator from the normal power source.
Failure to do so will result in death, serious injury,
and equipment damage.

WARNING

(000308)

Electric Shock. Verify all connections to the
cam lock receptacles are made to one side
only. Failure to do so could result in death,
serious injury and property damage.

(000155a)

WARNING

Electric shock. Only a trained and licensed electrician
should perform wiring and connections to unit. Failure to
follow proper installation requirements could result in death,
serious injury, and equipment or property damage.

Decal

Color—USA

Color—Canada

L1

Black

Red

L2

Red

Black

L3

Blue

Blue

N (Neutral)

White

White

G (Ground)

Green

Green

014019

(000157)

DANGER

Electrocution. Do not disable or modify the
connection box door safety switch. Doing so
will result in death or serious injury.

«
...
36
37
38
39
40
...
»

Содержание MDE570P

















































































Отзывы:

Нет отзывов