manualshive.com logo in svg

Generac Mobile MDE570P, Руководство пользователя, Страница: 37 / 80

Поделиться
Скачать
Generac Mobile MDE570P Скачать руководство пользователя страница 37

Owner’s Manual for Mobile Generator

33

•

The  door  covering  the  cam  lock  receptacles  (if

equipped) is open.

•

The link board cover panel is removed.

•

The Emergency Stop switch is active.

Before switching the breaker ON (I), verify ALL problems

causing breaker-trip are resolved.

NOTE: 

The  MLCB  controls  power  ONLY  to  the

connection lugs and cam lock receptacles (if equipped).

It  does  NOT  control  power  to  the  convenience

receptacles. When the main circuit breaker is OFF (O),

convenience  receptacles  remain  powered.  Each

convenience  receptacle  is  controlled  by  an  individual

circuit breaker, located near the receptacle. Verify the 20/

50 A fuses for the respective circuits.

Motorized Breaker (If Equipped)

Units  with  paralleling  function  are  equipped  with  a

motorized  main  circuit  breaker.  The  motorized  breaker

can be closed electronically, through the controller.

Connection Lugs

The installation should be in compliance with the national

electrical code (NEC), state, and local regulations.
See 

Figure 3-11

. Generator connection lugs are on the

unit backside, behind the lug box door. The lugs provide

connection  points  to  attach  external  loads  to  the

generator.

Figure 3-11. Connection Lugs

Decals above the connection lugs identify the lugs.

Connecting to Lugs

Connect to the lugs by routing power cables through the

opening in the bottom of the door.

IMPORTANT  NOTE:  Do  not  make  any  connections

directly  to  the  lugs  without  routing  the  cables

through the opening. Use a hex-wrench to tighten the

cable connections. 
IMPORTANT  NOTE:  There  is  permanent  conductor

between  the  generator  (stator  winding)  and  the

frame.

The connection lug door is equipped with safety interlock

switches. If the door is opened when the unit is operating,

the  interlock  switches  trip  the  main  circuit  breaker,

disable the voltage regulator, and shut down the unit.
See 

Figure 3-12

. A ground connection (A) is located on

the curbside rear exterior of the generator. The unit must

be connected to ground for proper operating safety. The

generator neutral is bonded to ground when it is shipped

from  the  factory.  The  bonding  plate  must  be  removed

when the generator is used as a standby power source.

Installation  should  be  in  compliance  with  the  National

Electrical Code (NEC), state, and local regulations.

(000237)

DANGER

Electrical backfeed. Use only approved switchgear to 
isolate generator from the normal power source.
Failure to do so will result in death, serious injury, 
and equipment damage.

(000157)

DANGER

Electrocution. Do not disable or modify the
connection box door safety switch. Doing so
will result in death or serious injury.

(000156)

DANGER

Electrocution. Before connections are made to
the unit, verify the main circuit breaker and
battery disconnect switch are OFF. Failure to do 
so will result in death or serious injury.

(000155a)

WARNING

Electric shock. Only a trained and licensed electrician 
should perform wiring and connections to unit. Failure to 
follow proper installation requirements could result in death, 
serious injury, and equipment or property damage.

Decal

L1
L2
L3
N (Neutral)
G (Ground)

014018

Содержание MDE570P

















































































Отзывы:

Нет отзывов