Generac Mobile MDE570P Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 80

Generac Mobile MDE570P Скачать руководство пользователя страница 33

Owner’s Manual for Mobile Generator

29

3.

Loosen nuts securing link board plate to panel.

4.

Position link board according to the correct config

-

uration, to obtain the desired output voltage.

5.

Tighten nuts 40 ft-lb (54.2 Nm).

6.

See

and

. Verify toggle switch

(A) is in correct position for the desired voltage.

Figure 3-2. Link Board

7.

Install link board cover panel. Tighten bolts to 10 ft-

lb (13.6 Nm).

Lockout Function

The link board is equipped with a lockout mechanism.

When engaged, the switch is locked in place, preventing

configuration changes. If an attempt is made to access

the link board, the controller will shunt trip the breaker

and stop the engine.

Manually Starting the Unit

To start the generator in MANUAL mode:

1.

Switch the battery disconnect switch to the ON

position.

Figure 3-3. Battery Disconnect Switch

NOTE:

See

. The Home page displays when

the controller is ON, and no other page has been

selected. The controller is in STOP mode.

Figure 3-4. Home Page

2.

Press the AUTO/MANUAL mode button to start

MANUAL mode.

NOTE:

The controller can be started from any page

when MANUAL mode is active.

3.

Press the green Engine START (I) button on the

controller to initiate the engine startup process.

The unit starts if there are no engine faults prevent

-

ing the unit from starting.

NOTE:

It may take a few seconds for the engine to run

smoothly and reach operating speed. During this time, a

Table 3-2. Link Board Positions, Voltage Settings

Rocker Switch

Up

Down

Link Board

Up

240 VAC

208 VAC

Down

600 VAC*

480 VAC

* If equipped. If unit does not have 600 VAC capability, it

will default to 480 VAC.

A

014012

(000103)

Asphyxiation. Running engines produce carbon
monoxide, a colorless, odorless, poisonous
gas. Carbon monoxide, if not avoided, will
result in death or serious injury.

DANGER

(000108)

WARNING

Hot Surfaces. When operating machine, do not
touch hot surfaces. Keep machine away from
combustibles during use. Hot surfaces could
result in severe burns or fire.

WARNING

(000281)

Fire risk. Fuel and vapors are extremely
flammable. Do not operate indoors. Doing
so could result in death, serious injury, or
property or equipment damage.

014014

011608

Status

Generator at Rest

Stop Mode

22:31

«
...
31
32
33
34
35
...
»

Содержание MDE570P

















































































Отзывы:

Нет отзывов