Generac Mobile MDE570P Скачать руководство пользователя страница 46

Страница: 46 / 80

Owner’s Manual for Mobile Generator

•

Inspect coolant level. Coolant should be visible in

the sight-glass, located on the top tank of the

radiator. Fill as needed.

Fuel Recommendations

IMPORTANT NOTE: DO NOT use home heating oil or

bio-diesel fuel.
IMPORTANT NOTE: Comply with all laws regulating

the storage and handling of fuels.

This unit is designed to operate with diesel fuel. Follow

these guidelines:

•

Use only ultra-low-sulfur (15 ppm) diesel fuel.

•

When temperatures are at or below freezing, use

No. 1 diesel fuel.

•

When temperatures are above freezing, use No. 2

diesel fuel.

•

In some areas of the country, climatized fuel—a

mixture of 1D and 2D, may also be used.

For more information, see the OEM engine manual

(Generac publication PN A0001715045),

Maintenance

section.

Adding Fuel

NOTE:

Never allow dust, foreign matter, or water to

enter fuel tank.

NOTE:

See

Specifications

for fuel tank capacity.

Place unit on a firm, level surface in a well venti

lated area.

Verify unit is OFF.

Remove fuel fill cap.

Fill tank with diesel fuel to 0.25 in (6.4 mm) from

the bottom of fill neck to allow for fuel expansion.

See

Resetting Maintenance Alarms

. Install fuel

fill cap.

NOTE:

Properly contain, clean, and dispose of spilled

fuel.
The fuel tank can be filled via the externally mounted fill

neck located on the rear corner roadside panel of the

machine. The fuel tank level can be monitored on the

control panel display or the analog gauge located on top

of the fuel tank near the battery tray on roadside of the

machine. The fill neck can accept nozzles up to 1.5"

(38mm) but flow rate should be limited to less than 65

GPM (246 LPM) to prevent blow back of fuel. When filling

the tank, never top off the tank such that the fill neck is

filled with diesel fuel. This will prevent fuel spills and

allow proper tank ventilation.
The standard fuel tank does not come equipped with fuel

containment or fuel tank drain. If fuel ever needs to be

drained from tank, it should be pumped out of the tank

and into a proper container.
The optional fuel tank does come equipped with fuel

containment and a rupture basin alarm. This alarm will

display a warning message on the controller display. The

fuel can be drained from the containment basin using the

drain plug located on the bottom of the tank.

Engine Oil Recommendations

To maintain the product warranty, the engine oil should

be serviced in accordance with the recommendations of

this manual.The engine has been filled with factory

engine oil of a grade recommended by the engine

supplier.
Use a high quality detergent oil with an appropriate

classification and viscosity for the engine type and

ambient temperature conditions. Contact a GMASD or

refer to the applicable engine service manual for more

information.

Commercial Oils

Perkins recommends use of Perkins Diesel Engine Oil for

all Perkins engines. Perkins unique oil formulations have

been developed to provide full performance and

maximum service life of your engine, and in tests have

been shown to provide superior protection. Available in

suitable API classifications to meet the emissions

requirements and performance of your engine, see

Table 4-3

for the correct oil specification for your engine.

Consult your Perkins distributor for more information on

these multi-grade oils.

IMPORTANT NOTE: Perkins requires the use of the

following specification of engine oil. Failure to use

the appropriate specification of engine oil will reduce

the life of your engine. Failure to use the appropriate

specification of engine oil will also reduce the life of

your aftertreatment system.

Explosion and Fire. Fuel and vapors are
extremely flammable and explosive. Keep fire
and spark away. Failure to do so will result
in death or serious injury.

(000168)

DANGER

(000204)

DANGER

Explosion and Fire. Do not overfill fuel tank.
Overfilling may cause fuel to leak and ignite
or explode, resulting in death or serious
injury.

Table 4-3. Oil Specifications

API CK-4
ACEA E9
ECF-3

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 46 / 80

Результаты поиска

Содержание MDE570P

Отзывы: