GEDA 300 Z Скачать руководство пользователя страница 71

Страница: 71 / 104

300 Z/ZP 2

Operation

BL144 GB 2019-11

Only the platform control is activated.

With the platform control activated, the machine has to be used as a

transport platform.

In the lower safety area, the move command button (3/4) must be

pressed for approx. 3 s until the platform moves. During this time,

a warning signal is emitted.

Each time after entering the platform, the platform control has to

be activated!

Travelling UP



Press and hold the

button (3).



The platform only moves while the

button (3) is pressed.

Stop UP travel



Release the

button (3).



The platform reaches the UP END stop rail and automatically

stops (the UP limit switch switches off).

Stop at landing level

If the platform is to be exited at a transfer point (landing level

equipment) for loading and unloading, the platform must be stopped so

that it is level with the landing-level safety door.

A LANDING LEVEL limit switch bar appropriate to the landing level

safety gate has to be installed (refer to the Assembly Manual).

Always approach the LANDING LEVEL stop rail from below.



Before reaching the landing level safety gate, press the

LANDING

LEVEL STOP

button (2) in addition to the

button (3).



The platform stops at the next landing level.



First release the

button (3) and then the

LANDING LEVEL

STOP

button (2) [or both at the same time].

Travelling DOWN



Press and hold the

DOWN

button (4).



The platform only moves while the DOWN button (4) is pressed.

Stop DOWN travel



Release the

DOWN

button (4).



The platform descends and stops automatically above the lower

safety area.

Содержание 300 Z









































































































Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды

GEDA 300 Z, Руководство по эксплуатации

Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды