GEDA 300 Z Скачать руководство пользователя страница 42

Страница: 42 / 104

Operation

300 Z/ZP 2

BL144 GB 2019-11

4.3.1

Securing the lowest stop position (ground station)

The lowest stop position must be secured and marked to prevent

unauthorized access.

DANGER

Danger to life from lowering platform



Never remain inside the cordoned area/base enclosure during

operation.



Whilst working inside the base enclosure, switch off the main

switch and secure it against being switched on. Secure the

platform, if necessary, or activate the setting on permanent

machines.

Operating the transport platform as per EN 16719

•

If the underrun protection is installed below the platform, a cordon is

sufficient for securing the ground station

•

Without underrun protection, a 1.10 m base enclosure with a barrier

with limit switch monitoring

a 2.00 base enclosure with barrier with sliding door has to be

installed

The transport platform must not be operated without a cordoned

off zone or base enclosure.

WARNING

Risk of injury



The distance of the cordon/base enclosure to moving hoist parts

must be a minimum of 0.5 m and maximum of 2.0 m.

Содержание 300 Z









































































































Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды

GEDA 300 Z, Руководство по эксплуатации

Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды