GEDA 300 Z Скачать руководство пользователя страница 73

Страница: 73 / 104

300 Z/ZP 2

Operation

BL144 GB 2019-11

4.3.6

Controls for special operation

4.3.6.1

Operation for assembly

For assembly, it is only possible to operate the hoist from the platform in

dead man's control. The platform only operates while the operating

button is pressed.

The ramp, barrier with unloading ramp and assembly plank must be

closed and engaged. The assembly guard must be properly attached at

the top.



Turn the main switch (on the ground station switch box) to the "I"

position (ON).

The key switch (10) must be turned to

the right ("1" position).
The LED display (7) of the selected

operating mode lights up.

Fig. 44: Selector switch for operating

mode, assembly

In this position, the key cannot be removed.

Only the platform control is activated for assembly.

WARNING

Key for authorized persons

The key (10) may only be used by assembly and maintenance

personnel!

Содержание 300 Z









































































































Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды

GEDA 300 Z, Руководство по эксплуатации

Результаты поиска

Содержание 300 Z

Отзывы:

Похожие инструкции для 300 Z

Бренды по названию

Популярные бренды