GEDA 1500z Скачать руководство пользователя

Страница: 57 / 84

GEDA

1500 Z/ZP

Operation

BL076 GB Edition 07.2015

57 / 84

Operating Manual

4.1.1

Special safety instructions for operation as a material hoist

•

Transporting persons is prohibited!

−

Switch to transport platform to carry out assembly and maintenance
tasks.

•

Operation of the material hoist must take place outside the danger

zone.

•

The operator must always be able to observe the platform.

4.1.2

Special safety instructions for operation as a transport
platform

•

Operation of the transport platform must be carried out exclusively

from the platform control.

•

Particular care is required near ground level.

•

A max. of 7 person (including the platform operator) may be

transported, whereby the corresponding proportion of transported
materials must be reduced.

•

Comply with the instructions of the platform operator.

•

Do not reach or lean out over the platform sides.

•

Do not step over material that is being transported.



The brake release lever must never be used to lower the platform
during operation. It is intended only for use in emergencies
(refer to Chapter

5.4.2).

Содержание 1500z





















































































Результаты поиска

Содержание 1500z

Отзывы:

Похожие инструкции для 1500z

Бренды по названию

Популярные бренды

GEDA 1500z, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание 1500z

Отзывы:

Похожие инструкции для 1500z

Бренды по названию

Популярные бренды