GE TLE 160 Скачать руководство пользователя

Страница: 36 / 91

Critical Power

Modifications reserved

Page 36/91

GE_UPS_USM_TLE_SUL_M16_M50_2bU_V010.docx

User Manual

TLE Series 160 - 500 UL S2B

Code

Alarm

Description

4104

BATTERY FUSES FAILURE

This function, when enabled on input programmable

relays (password required), warns the user about the

external Battery Fuses failure or MCB opening.

Signaled by NO free contact.

4105

RECTIFIER OVERTEMPERATURE

Temperature sensor indicates a situation of

overtemperature on the Rectifier bridge.

Only the alarm is given.

The Rectifier, when in an Off state, cannot start as

long as this condition persists.

4106

RECTIFIER TRANSFORMER

OVERTEMPERATURE

The temperature sensor inside the input

transformer winding indicates overtemperature.

Only the alarm is given.

The Rectifier, when in an Off state, cannot start as

long as this condition persists.

4110

RECTIFIER UTILITY OUT OF

TOLERANCE

Rectifier Input Utility is out of tolerance (voltage,

frequency or phase).

4115

LOW BATTERY VOLTAGE

The Battery has been discharged and reached

“stop operation” time-out (default 3 minutes), and

the Inverter will be shut down.

It will restart automatically only when the Battery

has recharged enough for a minimum runtime.

4116

HIGH BATTERY VOLTAGE

Dangerous high DC Voltage caused Inverter shut-

down.

Inverter restarts automatically after Battery returns

to floating voltage.

4117

BATTERY EARTH FAULT

A leakage current to earth has been detected on

the DC circuit.

4118

BATTERY FAULT

During battery test the voltage falls under the

critical level (depending setting parameters).

Battery test is stopped.

4121

HIGH DC RIPPLE

A high ripple is present in the battery voltage.

4125

HIGH DC-LINK VOLTAGE

Detection of high voltage on the DC-link.

The rectifier, booster and Inverter will switch off for

protection purposes.

The rectifier may only be switched on again if the

DC-Link’s voltage value falls below 430V.

4126

LEG CONTROL SATURATION (Imax) The current in the fourth leg has reached its highest

value.

4130

TURN ON RECT. OR SHUTDOWN UPS

Rectifier and Inverter are OFF.

The DC power supply is discharging the Battery.

Rectifier must be restarted or Battery must be

disconnected in order to avoid damage.

4140

RECTIFIER CONTROL FAILURE

Rectifier Voltage hasn’t reached the set value

(probably fault on regulation loop).

LED Rectifier on control panel is blinking.

4141

ISMAX DETECTION RECTIFIER

After 3 IS-Max condition within the time frame

specified in respective parameter, the Rectifier

remains shut-down.

4142

RECTIFIER CURRENT MAX

Will cause immediate shut-down of the Rectifier.

Based on the value inserted in the respective

parameter.

Содержание TLE 160




























































































Результаты поиска

Содержание TLE 160

Отзывы:

Похожие инструкции для TLE 160

Бренды по названию

Популярные бренды

GE TLE 160, Руководство пользователя

Результаты поиска

Содержание TLE 160

Отзывы:

Похожие инструкции для TLE 160

Бренды по названию

Популярные бренды