GE TLE 160 Скачать руководство пользователя

Страница: 40 / 91

Critical Power

Modifications reserved

Page 40/91

GE_UPS_USM_TLE_SUL_M16_M50_2bU_V010.docx

User Manual

TLE Series 160 - 500 UL S2B

6.3.3

Messages list

Code

Message

Description

4002

WATCHDOG RESET

The microprocessor has detected an incorrect

operation:

Transfers the load on utility and performs a

program reset.

The Inverter will restart automatically and will

supply the load.

4003

SENSOR AUTO-CALIBRATION ERROR

The voltage/current reading were not correctly

calibrated when the UPS was switched on.

4111

RECTIFIER UTILITY OK

Rectifier Input Utility is again within the admitted

tolerance (voltage, frequency and phase).

4119

BATTERY TEST STARTED

Start of Manual or Automatic Battery Test.

4120

BATTERY TEST STOPPED

End of Manual or Automatic Battery Test.

4122

MANUAL BOOST CHARGE START

Recharging has been manually activated from

the control panel, bringing the final load up to the

value of the respective parameter.

4123

AUTOMATIC BOOST CHARGE START

After the battery has discharged, an automatic

boost charge has started to recharge the battery

based on pre-defined settings.

4124

MANUAL/AUTOMATIC BOOST CHARGE

STOP

The automatic boost charge has finished. The

battery’s voltage will return to the maintenance

value.

A manually activated boost charge will finish if: it

is manually interrupted, the initial timer setting

has expired, or the rectifier is not functioning

correctly (Alarm 4140).

The battery voltage will return to the

maintenance value.

4144

BOOSTER ON

The booster is switched ON.

It transfers energy from the battery to the DC-

link.

4145

BOOSTER OFF

The booster is switched Off.

4148

BATTERY CHARGER ON

The battery charger is switched on and is

charging the battery.

4149

BATTERY CHARGER OFF

The battery charger is switched off.

4161

RECTIFIER ON

Rectifier started.

4162

RECTIFIER OFF

Rectifier shut-down.

4163

GENERATOR ON

Customer Interface (X1 - 11, 22) received a Gen-

set ON signal.

Operating mode depend on setting of

Parameters.

4164

GENERATOR OFF

Customer Interface (X1 - 11, 22) received a Gen-

set OFF signal.

Function Bypass enabled depends on setting of

Parameter.

4302

INVERTER CANNOT BE TURNED ON

Inverter cannot be switched on because one of

the following conditions is still present:

- Overtemperature

- K7 opening Failure

- Low Battery Voltage - High Battery Voltage

- Inverter Fuses

- DC Low

- Overload

- EPO - Emergency Power Off

Содержание TLE 160




























































































Результаты поиска

Содержание TLE 160

Отзывы:

Похожие инструкции для TLE 160

Бренды по названию

Популярные бренды

GE TLE 160, Руководство пользователя

Результаты поиска

Содержание TLE 160

Отзывы:

Похожие инструкции для TLE 160

Бренды по названию

Популярные бренды