GE ReadyToProcess WAVE 25 Скачать руководство пользователя страница 75

Страница: 75 / 172

4.1.1

Delivery and storage

When you receive the delivery
boxes

•

Record on the packing slip if there is any apparent damage on the delivery boxes.
Inform your GE representative of any such damage.

•

Move the delivery boxes to a protected location indoors.

Storage requirements

The delivery boxes should be stored in a protected location indoors. The following storage
requirements must be fulfilled for the unopened boxes.

Allowed range

Parameter

-25°C to 50°C

Ambient temperature, storage

5% to 95% (non-condensing)

Humidity, storage

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

4 Installation

4.1 Site preparation

4.1.1 Delivery and storage

Содержание ReadyToProcess WAVE 25













































































































































































Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды

GE ReadyToProcess WAVE 25, Руководство по эксплуатации

Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды