GE ReadyToProcess WAVE 25 Скачать руководство пользователя страница 127

Страница: 127 / 172

5.2.3

Configure system properties

Edit the system properties whenever the configuration of the system is changed, for
example, to

•

switch between single and dual modes.

•

change the system setup, for example if a CBCU or pump has been added or removed.

•

change the Instrument Configuration of the system.

The Instrument Configuration is the system specific control software. It is provided
on a DVD with the system, and is also available for download. Contact your GE rep-
resentative if you need help to download the Instrument Configuration.

Follow the instructions below to edit the system properties.

Action

Step

Open the Administration module in the Tools menu.

Click System Properties.

Select your system in the System Properties dialog and click Edit.

Note:

Only systems that are switched on and connected to the computer can be
edited.

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

127

5 Operation

5.2 Start and configure the system

5.2.3 Configure system properties

Содержание ReadyToProcess WAVE 25













































































































































































Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды

GE ReadyToProcess WAVE 25, Руководство по эксплуатации

Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды