GE ReadyToProcess WAVE 25 Скачать руководство пользователя страница 56

Страница: 56 / 172

Status LEDs

The status LEDs indicate the pumping function status according to the following table.

Description

Light indicator

The pumping function is ready for operation.

Steady green light

Pumping is ongoing.

Green flashing light

Indicates an internal error, but the pump is still operating.

Red flashing light

Indicates an internal error, and the pump is not operating
properly.

Steady red light

Rear view of the pump

The illustration below shows the rear panel of the pump.

Description

Component

Part

Power connection to the rocker.

UniNet-9 port

Indicates system connection status.

CAN indicator LED

Shows the unit number of the pump for recognition
by the system.

CAN ID switch

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

3 System description

3.4 ReadyToProcess Pump 25

Содержание ReadyToProcess WAVE 25













































































































































































Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды

GE ReadyToProcess WAVE 25, Руководство по эксплуатации

Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды