GE ReadyToProcess WAVE 25 Скачать руководство пользователя страница 15

Страница: 15 / 172

1.4

Important concepts

Concepts and abbreviations used in this manual are explained in the table below.

Explanation

Concept/
abbreviation

The disposable container in which the cells are cul-
tured.

Cellbag™ bioreactor

Dissolved oxygen.

Optical sensor for measurement of dissolved oxygen.
Attached to DO configured Cellbag bioreactors.

DO sensor

Operating mode with one Cellbag bioreactor on the
rocker.

Single mode

Operating mode with two Cellbag bioreactors on the
same rocker. Cultivation is monitored and controlled
independently in the two bioreactors.

Dual mode

Optical sensor for pH measurement. Attached to pH
configured Cellbag bioreactors.

pH sensor

Control unit for gas mix, pH and DO control.

ReadyToProcess™ CBCU

The pump.

ReadyToProcess Pump 25

The rocker.

ReadyToProcess WAVE 25
rocker

Tray for Cellbag, mounted on the rocker. Different
tray sizes are available for different culture capacities.

Tray

The entire bioreactor system, including rocker,
CBCU(s), and pump(s), together with Cellbag bioreac-
tor(s) and filter heater(s).

ReadyToProcess WAVE 25

The ReadyToProcess WAVE
25 system

The bioreactor system

The software used for controlling and monitoring the
system.

UNICORN

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

1 Introduction

1.4 Important concepts

Содержание ReadyToProcess WAVE 25













































































































































































Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды

GE ReadyToProcess WAVE 25, Руководство по эксплуатации

Результаты поиска

Содержание ReadyToProcess WAVE 25

Отзывы:

Бренды по названию

Популярные бренды