gc Aadva Lab Scanner 2 Скачать руководство пользователя страница 3

Страница: 3 / 56

Aadva Lab Scanner 2

Manual

Table of contents

1. About 4

Introduction 4
Warnings 5

2. For your safety

2.1. Proper use

2.2. General safety instructions

2.3. Symbols on the device

3. Scope of delivery

4. Device components

4.1. Front view

4.2. Internal view

4.3. Views of the accessories (standard scope of delivery)

4.4. Connections and type plate (rear view)

5. Setup and commissioning of the scanner

5.1. Choosing a workstation

5.2. Unpacking the scanner

5.3. Connecting the scanner

5.4. Aadva Scan installation

6. The object holder system

6.1. Overview

6.2. Matting the surface with 3D scan spray

7. Positioning of a single jaw model

7.1. Inserting a jaw model with a Multisplit mounting plate

7.2. Inserting a jaw model with an adapter plate

7.3. Inserting a jaw model with an object holder

7.4. Fastening gingiva, squeeze bites, scanbodies or wax-ups

8. Positioning of non-articulated occlusion models

8.1. Fastening an occlusion model with a rubber band

8.2. Fastening of an occlusion model with an occlusion clamp

9. Positioning of articulated occlusal models

9.1. Positioning of an occlusal model with an articulator

10. Positioning tooth stump models with

the Multi die adapter

11. Positioning of a Triple Tray® impression

12. Positioning objects (universal mode)

12.1. Fastening objects on the flexible object holder

12.2. Inserting the object holder

12.3. Removing the object holder

13. Positioning the calibration model

14. Operating principle of the scanner

14.1. Operation via touchscreen

14.2. Switching between LR and HR mode

15. Device maintenance

16. Faults and repairs

17. Environmentally-friendly disposal

17.1. Disposal of the packaging

17.2. Disposal of the device

18. Technical specifications

20. Glossary

Содержание Aadva Lab Scanner 2

























































Результаты поиска

Содержание Aadva Lab Scanner 2

Отзывы:

Похожие инструкции для Aadva Lab Scanner 2

Бренды по названию

Популярные бренды

gc Aadva Lab Scanner 2, Руководство пользователя

Результаты поиска

Содержание Aadva Lab Scanner 2

Отзывы:

Похожие инструкции для Aadva Lab Scanner 2

Бренды по названию

Популярные бренды