Gazelle SOBOL Скачать руководство пользователя страница 35

Страница: 35 / 87

Positions of instruments on the vehicles with Sofim 8140. 43C engine are given

in Fig. 4.15.

Fig. 4.15.

Instrument cluster

1 2 3 4 5 6 7 8 9 10 11 12 13 14

1. Voltmeter.
2. Warning lamp of glow plug cuttingin.

If the warning lamp lights up after turning on of the engine control switch

and then goes out, it means that the engine is ready to be started up. When the
thermostarter is defective the warning lamp does not light.

3. Warning lamp (orange) of antilock brake system (ABS)

(for buses).

4. Warning lamp (red) “STOP”.
5. Warning lamp (green) of left turn indicators.
6. Warning lamp (red) of brake fluid low level.

Lights up

when

brake fluid level in the master cylinder becomes lower than

allowed.

7. Total distance counter.
8. Speedometer.
9. Warning lamp (red) of parking brake engagement.

Starts flashing after turning on of the engine control switch if the parking

brake is engaged.

10. Warning lamp (green) of right turn indicators.
11. Warning lamp (red) of oil pressure drop.

Lights up when the engine

control switch is turned on. The lamp may glow with the engine running at
idle speed and at sharp braking. The lamp should go out when the engine speed

Содержание SOBOL
























































































Результаты поиска

Содержание SOBOL

Отзывы:

Похожие инструкции для SOBOL

Бренды по названию

Популярные бренды

Gazelle SOBOL, Руководство по эксплуатации

Результаты поиска

Содержание SOBOL

Отзывы:

Похожие инструкции для SOBOL

Бренды по названию

Популярные бренды