manualshive.com logo in svg

GAS GAS WILD HP 450, Руководство по обслуживанию, Страница: 8 / 63

Поделиться
Скачать
GAS GAS WILD HP 450 Скачать руководство пользователя страница 8

WILD HP -

73

-

of obstacles and with no other vehicles around first. Read the
recommendations in the section "Use of the QUAD" of this manual.

- The same applies to steep climbs or descends. Start testing your
skills with minimum slopes and raise the difficulty level little by little.
Advice on this point is also included in the section mentioned above.

- In case you stall the engine, follow the procedure described in the
manual. If the engine stalls and the vehicle starts going backwards,
follow the special braking procedure described in the manual. Climb
off the vehicle to the higher side of the slope.

- Remember that your safety comes before the machine's, and it is
important to keep this priority in mind.
-When going across a slope, move your weight to the higher side,
read the manual's advice on that. Avoid very slippery slopes or with
loose surface.

- Never try to overcome big obstacles, like rocks or trunks. This
vehicle has not been designed for that; it could be damaged and/or
you might be injured.

- Do not try to make the vehicle slide sideways if you don't dominate
the technique in depth, because it may be dangerous. Like in the
cases described above, do some testing on flat, wide and obstacle-
free ground beforehand and follow the advice described in this
manual. You must never lose control of the vehicle.

- This vehicle has been designed to go through a maximum depth
of 35 cm of water. Do not use the vehicle in fast moving water, read
the instructions for this type of terrain carefully. Take into account
that brake efficiency is diminished when wet. When coming out of
the water, brake several times so that they dry more quickly through
friction.

- Always use the tyre size and type described in this manual.

SAFETY INFORMATION

WARNING

Not following these instructions may lead to grave injuries or even
death.

The QUAD is not a toy: driving it may be dangerous.

The QUAD is driven differently form from other vehicles such as
cars and motorbikes. Even during routine manoeuvres like turns,
driving on hills or over obstacles, collisions or tumbles can be quickly
produced, if precautions are not taken.

- Do not drive the QUAD before reading the sections: "Safety
information", "Use of the QUAD", and "Main parts of the vehicle".
Even if you are an experienced QUAD driver, not all makes and
models are equal and it is necessary to know the machine in depth
before starting on your first outing.

- You are not allowed to carry a passenger, and the vehicle is not
equipped for that purpose.

- Sit correctly with both hands on the handlebars, your feet on the
footrests and your back straight up.

- Always control your speed according to your skills, the weather
conditions and the ground characteristics. Pay attention to changes
in the ground surface and control your speed when you are not
familiar with them.

- Always perform the routine checks described in this manual before
using the vehicle, to make sure it is in perfect operating conditions,

- Riding a QUAD is not like driving any other vehicle, and you will
notice it specially when cornering. Practise on flat ground with free

Содержание WILD HP 450
































































Отзывы:

Нет отзывов