manualshive.com logo in svg

GAS GAS WILD HP 450, Руководство по обслуживанию, Страница: 23 / 63

Поделиться
Скачать
GAS GAS WILD HP 450 Скачать руководство пользователя страница 23

WILD HP -

88

-

WARNING

The use of inadequate tyres or riding the vehicle with incorrect or
unequal tyre pressures may lead to loss of control, with the subsequent
risk of accident.

The tyres must be inflated to the recommended pressures. Measure
the tyre pressure with a low pressure gauge.

CAUTION

Check and adjust the pressures with cold tyres.

Pressures must be the same on both sides.

1

Tyre wear-out limit:

Observe how the tyre wears out. If the tyre is worn out at the centre,
it means that the pressure is too high.
If the tyre wears out at the edges, the tyre pressure is too low.
The tyre must be worn out equally on its surface.
Replace the tyre when the groove depth is below 3mm.

Manufacturer

MAXIS
MAXIS

Size

21 x 7,00 - 10"
20 x 11,00 - 9"

Type

RAZR
RAZR

Front
Rear

Recommended

0,400 bar/ 40 Kpa
0,450 - 0,500 bar/
45 - 50 Kpa

Minimum

0,370 bar/ 37 Kpa
0,420 - 0,470 bar/
42 - 47 Kpa

Maximum

0,430 bar/ 43 Kpa
0,480 - 0,530 bar/
48 - 53 Kpa

Front
Rear

M i n i m u m
stud depth
(1): 3 mm.

Содержание WILD HP 450
































































Отзывы:

Нет отзывов