GAS GAS WILD HP 450 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 63

GAS GAS WILD HP 450 Скачать руководство пользователя страница 53

WILD HP -

118

-

The top button is the reset button.
The bottom button is the mode button.

The initial display is the clock.(time) if you press mode (btm. button)
the display goes:

1. Speedometer.
2. Speed (Km or miles).
3. Total distance in kmh or miles (this has a memory even if battery
disconnected).
4. Trip distance.

To change the time:

- Press mode until time display is shown.
- Press mode again keeping the button pressed the hour will display
only add the hours by pressing the reset (top) button.
- Press mode again to adjust the minutes in the same way.
- Press mode again and the time is now set.

(when you have set the time the seconds automatically start from
zero )

Trip distance:

- From time display press mode 3 times. (l- 0) to zero the trip , keep
the reset button pressed until it zeros.

To change to kilometers per hour or miles per hour:

- Disconnect the battery. (the total distance will be saved).
- Re-connect the battery whilst holding down either button and it will
read either;
- The white plastic block connector on the speedo is for the display
backlight.
- The red wire is positve.
- The black wire is negative.

- Warning; your speedo is set for the diameter of your front wheel

If you get the display to read "a 00" then you are in the rolling radius
changing mode. you can "trim" the speed to run fast or slow.
It ranges from "a-25" to "a 25".

NOTE

Standard setting is "a 00", we recommend you keep it at that.

00:00

Reset

Mode

(For change the display mode, you need press mode button .)

0

Speed

00:00

Clock / chrono

0.0

Trip Distance

0000

Total Distance

MULTIFUNCTION

«
...
51
52
53
54
55
...
»

Содержание WILD HP 450
































































Отзывы:

Нет отзывов