manualshive.com logo in svg

GAS GAS WILD HP 450, Руководство по обслуживанию, Страница: 56 / 63

Поделиться
Скачать
GAS GAS WILD HP 450 Скачать руководство пользователя страница 56

WILD HP -

121

-

TROUBLESHOOTING

NOTE

This is not an exhaustive list, giving every possible cause for each problem listed. It is meant simply as a rough guide to assist the

troubleshooting for some of the more common difficulties.

TROUBLE

CAUSE

REMEDY

Starter engine doesn't crank

Engine doesn't crank

Engine cranks but doesn't start

- Blown fuse in the starter relay.

- Discharged battery.

- Low outside temperatur

- Crankshaft seizure.
- Cylinder-piston, connecting rod big end
seizure.
- Transmission set seizure.

- Fuel supply interrrupted.

- The motorcycle has been out of operation
for a longer period of time. Therefore old
fuel has accumulated in the float chamber.
- Scooty or wet spark plug.
- Flooded engine.

- The plug connection of the CDI unit, the
pulse generator or the ignition coil has
oxydized.
- Fuel/ air mixture incorrect.

1

2

3

- Dismount the right paneling and the filter box cover and
replace the fuse in the starter relay.
- Recharge the battery and investigate the causes for
discharging; contact a KTM dealer.
- Start engine with start pedal.

- Go to specialized garage.
- Go to specialized garage.

- Go to specialized garage.

- Check fuel pump relay, extract air filter cover, check fuel
pump isn't glogged.
- Is recomended to drain the old fuel from the float chamber.

- Clean and dry the spark plug or exchange it, respectively.
- In order to "pump the engine free", pull de starter pedal 5
or 10 times or actuate the kickstarter 2 times in 5 seconds.
Then, start the engine as described above. If the engine fails
to start, unscrew the spark pulug and dry it.
- Remove the seat and the fuel tank. Clean the plug connection
and treat it with contact spray.

- Clean tank cap air vent. Check by-pass throttle body. Check
the air filter.

Содержание WILD HP 450
































































Отзывы:

Нет отзывов