manualshive.com logo in svg

GAS GAS WILD HP 450, Руководство по обслуживанию, Страница: 50 / 63

Поделиться
Скачать
GAS GAS WILD HP 450 Скачать руководство пользователя страница 50

WILD HP -

115

-

CLEANING, LUBRICATION AND STORAGE

CLEANING

Frequently cleaning your vehicle will not serve only to improve its
aspect, but also to improve its overall performance and to make the
life of most of its parts longer.

Before washing the quad some precautions need to be taken to
prevent water from entering some parts:

- If the outside of the engine has too much grease on it, apply a
degreaser with a brush. Do not apply this product to the chain,
sprockets or wheel axles.

- Eliminate all dirt and the degreaser by washing them off with a
garden hose. Reduce the water pressure to the minimum required
for this job.

CAUTION

Excessive water pressure may make it infiltrate in the wheel bearings,
brakes, transmission bushings and electric components, with the
subsequent damage.

10. Replace the drain caps and screw them back on. Pour new oil
through the dipstick hole. Approximately 1800 ml, or else the required
amount.

WARNING

The engine can be damaged if the oil is not used properly or the
specifications recommended by GAS GAS MOTOS are not followed.
Use the type of oil in the section of «recommended gasoline and oil
specifications».

11. Start the engine and let it idle for five minutes. Check that oil is
not leaking anywhere.

12. Check that the oil level is correct.

Silencer.

Clutch and brake levers, hand
grips, engine stop button

.

Air cleaner intake.

Spark plug cap and all filler
opening cover.

- Cover with a plastic bag secured with
rubber bands.
- Cover with a plastic bag.

- Close up the opening with tape or stuff
in rags.
- Avoid spraying water with any great
force near the following places.

Содержание WILD HP 450
































































Отзывы:

Нет отзывов